Endress+Hauser Proline Promag W 400

Other manuals for Endress+Hauser Proline Promag W 400

Technical Information92 pages

Brief Operating Instructions64 pages

Questions and Answers:

P
Peter HammondSep 10, 2025
Why is the local display dark but signal output is within range on Endress+Hauser Measuring Instruments?
- S
  Sean PattonSep 10, 2025
  If the local display on your Endress+Hauser Measuring Instruments is dark but the signal output is within the valid range, the display may be set too bright or too dark. Try adjusting the display by simultaneously pressing the indicated buttons to brighten or darken it. If this doesn't work, the display module may be defective and need to be replaced.
E
Erin CarterSep 9, 2025
What to do if Endress+Hauser Measuring Instruments show correct value on display but signal output is incorrect?
- S
  Stacy MarshSep 9, 2025
  If your Endress+Hauser Measuring Instruments show the correct value on the local display, but the signal output is incorrect (though still within the valid range), it is likely due to a configuration error. Check and correct the parameter configuration.
J
Joseph MorrisAug 25, 2025
Why is my Endress+Hauser Proline Promag W 400 device measuring incorrectly?
- T
  trosarioAug 25, 2025
  If your Endress+Hauser Measuring Instruments are measuring incorrectly, it could be due to a configuration error or because the device is being operated outside of its intended application. First, check and correct the parameter configuration. Also, ensure that you are observing the limit values specified in the "Technical Data".
D
dana72Sep 6, 2025
What causes no or incomplete display of contents in the Web browser for Endress+Hauser Proline Promag W 400 Measuring Instruments?
- D
  dillonkaylaSep 7, 2025
  If you experience no or incomplete display of contents in the web browser while using your Endress+Hauser Measuring Instruments, it may be because JavaScript is not enabled or cannot be enabled. Enable JavaScript. Also, enter http://192.168.1.212/ basic.html as the IP address.
J
jamespenningtonSep 5, 2025
Why is the backlighting of my Endress+Hauser Proline Promag W 400 Measuring Instruments local display red?
- G
  Gregory DavidsonSep 5, 2025
  If the backlighting of the local display on your Endress+Hauser Measuring Instruments is red, it indicates that a diagnostic event with "Alarm" diagnostic behavior has occurred. Take remedial measures ? ? 114.
A
Amber PetersenSep 4, 2025
How to change the language on Endress+Hauser Proline Promag W 400 Measuring Instruments local display?
- K
  Kim NelsonSep 4, 2025
  If the text on the local display of your Endress+Hauser Measuring Instruments appears in a foreign language that you cannot understand, it's likely that the incorrect operating language is configured. To change it: 1. Press ? + ? for 2 seconds (to reach the "home position"). 2. Press ?. 3. Set the desired language in the Language parameter.
R
Rebecca PetersenSep 3, 2025
What to check if Endress+Hauser Proline Promag W 400 has no connection via EtherNet/IP?
- K
  Keith HudsonSep 3, 2025
  If you have no connection via EtherNet/IP with your Endress+Hauser Measuring Instruments, the device plug may be connected incorrectly. Check the pin assignment of the device plug.
D
David HuberSep 2, 2025
Why is the content of Endress+Hauser Measuring Instruments Web browser incomplete or difficult to read?
- L
  Lindsey StokesSep 2, 2025
  If the content of your web browser is incomplete or difficult to read when accessing your Endress+Hauser Measuring Instruments: * You may not be using the optimum version of the web server. Use the correct web browser version ? ? 63. Clear the web browser cache and restart the web browser. * Unsuitable view settings may be in use. Change the font size/display ratio of the web browser.
R
Ronald AdkinsSep 1, 2025
Why is the Endress+Hauser Proline Promag W 400 local display dark but signal output is valid?
- B
  Briana Quinn MDSep 1, 2025
  If the local display on your Endress+Hauser Measuring Instruments is dark, but the signal output is within the valid range: * The display might be set too bright or too dark. To set the display brighter, simultaneously press ? + ?. To set the display darker, simultaneously press ? + ?. * The display module could be defective. Consider ordering spare part ? ? 124.
B
Bill RileyAug 31, 2025
Why do I have no write access to parameters on Endress+Hauser Proline Promag W 400 Measuring Instruments?
- T
  Tammy AllenAug 31, 2025
  If you have no write access to parameters on your Endress+Hauser Measuring Instruments: * Check if hardware write protection is enabled. If so, set the write protection switch on the main electronics module to the OFF position. * Verify if the current user role has limited access authorization. Check the user role ? ? 62 and enter the correct customer-specific access code ? ? 62.

Endress+Hauser Proline Promag W 400 Specifications

General

Measurement Principle	Electromagnetic
Housing Material	Aluminum, Stainless steel
Device Type	Flowmeter
Nominal Diameter	DN 15 to DN 400
Lining	PTFE
Electrode Material	316L stainless steel
Pressure Range	Up to 40 bar (depending on nominal diameter)
Output Signal	4 to 20 mA
Power Supply	24 V DC
Degree of Protection	IP67
Accuracy	±0.2% of the measured value