Epson TM-P20II Reference Guide

45
Table 10-11 Display items (Not supporting wireless functions)
Items
Description
Condition
"Device Name"
Shows the printer name currently used.
-
"Connection Status"
"Disconnect" / "10BASE-T, Half Duplex" / "10BASE-T,
Full Duplex" / "100BASE-TX, Half Duplex" /
"100BASE-TX, Full Duplex" / "1000BASE-T, Full duplex" /
"Unknown"
Shown when the wired LAN is used.
"Wi-Fi Disconnected" / "Searching for Wi-Fi" /
"W-Fi-xxxMbps" ("xxx": "00" - "495") / "Unknown"
Shown when the wi-fi is used.
"Signal Strength"
"Excellent" / "Good" / "Fair" / "No Good" / "Unknown"
Only shown when wireless LAN is
used. Not shown while Wi-Fi Direct
is used.
"Obtain IP Address"
"Auto" / "Manual"
-
"Set using BOOTP"
"Enable" / "Disable"
- If "Obtain IP Address" is "Manual",
this item is not shown.
"Set using Automatic
Private IP Addressing
(APIPA)"
"Enable" / "Disable"
- If "Obtain IP Address" is "Manual",
this item is not shown.
"IP Address"
"xxx.xxx.xxx.xxx"
xxx: 0 - 255 in decimal
-
"Subnet Mask"
"xxx.xxx.xxx.xxx"
xxx: 0 - 255 in decimal
-
"Default Gateway"
"xxx.xxx.xxx.xxx"
xxx: 0 - 255 in decimal
-
"DNS Server Setting"
"Auto" / "Manual"
-
"Primary DNS Server"
"xxx.xxx.xxx.xxx"
xxx: 0 - 255 in decimal
-
"Secondary DNS Server"
"xxx.xxx.xxx.xxx"
xxx: 0 - 255 in decimal
-
"Way of obtaining DNS
Host Name"
"Auto" / "Manual"
-
" DNS Host Name Status"
"Unknown" / "Successful" / "Failed"
Shown if the way of obtaining a DNS
host name is auto.
"DNS Host Name"
Shows the DNS host name currently used.
-
"Way of obtaining DNS
Domain Name"
"Auto" / "Manual"
-
"DNS Domain Name
Status"
"Unknown" / "Successful" / "Failed"
Shown if the way of obtaining a DNS
host name is auto.
"State of DNS Domain
Name obtained
automatically"
Shows the DNS domain name currently used.
-
"Proxy Server Setting"
"Do Not Use" / "Use"
-
"Proxy Server"
Shows the proxy server name in the IP address or
FQDN format.
- IP address format
"xxx.xxx.xxx.xxx"
xxx: 0 - 255 in decimal
- FQDN format
ASCII (alphanumeric, dot, hyphen), 1-255 characters
Shown when the value for "Proxy
Server Setting" is "Use".
"Proxy Server Port
Number"
Range of "0" - "65535" in decimal
Shown when the value for "Proxy
Server Setting" is "Use".
"Proxy Server User Name"
0 - 256byte alphanumeric characters
ASCII 0x20 - 0x7E
Shown when value of "Proxy Server
Setting" is "Use".
"Proxy Server Password"
"Not Set" / "**********"
Shown when value of "Proxy Server
Setting" is "Use".
"IPv6 Setting"
"Enable" / "Disable"
-
"IPv6 Anonymous
Address"
"Enable" / "Disable"
Shown if the IPv6 Setting is used.
"IPv6 DHCP Server
Setting"
"Do Not Use" / "Use"
Shown if IPv6 is enabled.
Not shown if the DHCPv6 function is
not supported.
"IPv6 Address"
Shows an IPv6 address.
Shown if the IPv6 Setting is used.
"IPv6 Address Default
Gateway"
Shows an IPv6 address.
Shown if the IPv6 Setting is used.
"IPv6 Link-Local Address"
Shows a valid IPv6 link-local address
Shown if the IPv6 Setting is used.

Epson TM-P20II Specifications

General

Brand	Epson
Model	TM-P20II
Category	Printer
Language	English