Epson TM-P20II

95
"Remote Gateway(Tunnel
Mode)"
Enter an IPv4 address or IPv6 address.
Max of 39 characters.
If "IPsec/IP Filtering" is "Enable" ,
"Access Control" is "IPsec" and
"Encapsulation" is "Tunnel
Mode" ,it is possible to set this
item.
"Security Protocol"
Use the drop-down list to make a choice.
"ESP" / "AH"
If "IPsec/IP Filtering" is "Enable"
and "Access Control" is "IPsec", ,it
is possible to set this item.
"Algorithm Settings"
Title strings. "IKE", "ESP", and "AH" are included.
-
"IKE"
Title strings. "Encryption", "Authentication" and "Key
Exchange" are contained.
-
"Encryption"
Use the drop-down list to choose from the following.
"AES-CBC-128" / "AES-CBC-192" / "AES-CBC-256" /
"3DES" / "Any"
This item is displayed when "IKE
Version" is "IKEv1".
This item is enabled when
"IPsec/IP Filtering" is "Enable",
"Access Control" is "IPsec".
"Encryption"
Use the drop-down list to choose from the following.
"AES-CBC-128" / "AES-CBC-192" / "AES-CBC-256" /
"AES-GCM-128" / "AES-GCM-192" / "AES-GCM-256" /
"3DES" / "Any"
This item is displayed when "IKE
Version" is "IKEv2".
This item is enabled when
"IPsec/IP Filtering" is "Enable",
"Access Control" is "IPsec".
"Authentication"
Use the drop-down list to choose from the following.
"SHA-1" / "SHA-256" / "SHA-384" / "SHA-512" / "MD5" /
"Any"
This item is enabled when
"IPsec/IP Filtering" is "Enable",
"Access Control" is "IPsec".
"Key Exchange"
Use the drop-down list to choose from the following.
"DH Group 1" / "DH Group 2" / "DH Group5" / "DH
Group14" / "DH Group15" / "DH Group16" / "DH
Group17" / "DH Group18" / "DH Group19" / "DH
Group20" / "DH Group21" / "DH Group22" / "DH
Group23" / "DH Group24" / "DH Group25" / "DH
Group26" / "Any"
This item is displayed when "IKE
Version" is "IKEv1".
This item is enabled when
"IPsec/IP Filtering" is "Enable",
"Access Control" is "IPsec".
"Key Exchange"
Use the drop-down list to choose from the following.
"DH Group 1" / "DH Group 2" / "DH Group5" / "DH
Group14" / "DH Group15" / "DH Group16" / "DH
Group17" / "DH Group18" / "DH Group19" / "DH
Group20" / "DH Group21" / "DH Group22" / "DH
Group23" / "DH Group24" / "DH Group25" / "DH
Group26" / "DH Group27" / "DH Group28" / "DH
Group29" / "DH Group30" / "Any"
This item is displayed when "IKE
Version" is "IKEv2".
This item is enabled when
"IPsec/IP Filtering" is "Enable",
"Access Control" is "IPsec".
"ESP"
Title strings. "Encryption" and "Authentication" are
contained.
-
"Encryption"
Use the drop-down list to choose from the following.
"AES-CBC-128" / "AES-CBC-192" / "AES-CBC-256" /
"AES-GCM-128" / "AES-GCM-192" / "AES-GCM-256" /
"3DES" / "Any"
This item is enabled when
"IPsec/IP Filtering" is "Enable",
"Access Control" is "IPsec" and
"Security Protocol" is "ESP".
"Authentication"
Use the drop-down list to choose from the following.
"SHA-1" / "SHA-256" / "SHA-384" / "SHA-512" / "MD5" /
"Any"
This item is enabled when
"IPsec/IP Filtering" is "Enable",
"Access Control" is "IPsec" and
"Security Protocol" is "ESP". This
item is disabled when
"Encryption" of "ESP" is
"AES-GCM-128" or "AES-GCM-192"
or "AES-GCM-256".