FAAC A1400 AIR RDT - Page 117

FAAC A1400 AIR RDT

118 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Translation of the original instructions

ENGLISH

Table of Contents

Default Chapter4
- EC Declaration of Conformity of a Machine4
- EC Declaration of Conformity4
- Declaration of Incorporation of Partly Completed Machinery5
- Table of Contents6
1 Introduction to the Instructions Manual9
- Safety Recommendations9
- Meaning of the Symbols Used10
- Symbols: Notes and Warnings on the Instructions10
- Symbols: Work Equipment (Type and Size)10
- Symbols: Safety Recommendations (en ISO 7010)11
- Symbols: Signs on the Product11
- Symbols: Personal Protective Equipment11
- Symbols: Signs on the Packaging11
2 Automation A1400 Air Rdt12
- Intended Use12
  - Limitations for Use12
- Unauthorised Use12
- Identification Plate13
- Technical Specifications14
- Composition of the Supply15
  - Installation Stages According to Type of Supply15
  - Components of the Automation16
3 Required Inspections and Arrangements18
- Preliminary Inspections18
- Arrangement of Electrical Cables18
4 Transport and Reception of the Consignment19
- Handle Packages19
- Unpack and Handle19
5 Cut the Profiles20
- Profile Cutting Measurements20
6 Assemble the Head Section21
- Preliminary for Self-Supporting Head Section (if Any)21
- Assemble the Components22
7 Assemble the Frame A1400 Air Rdt Cs26
- Entry Door with Profiles TK5026
- Entry Door with Profiles TK2027
8 Install the Head Section29
- Preliminary Operations29
- Wall Fastening29
- Self-Supporting Automation Fastening30
  - Mount the Transom31
9 Install Leaves32
- Mount the Lower Shoes32
- Mount Profiles on the Leaves33
- Mount the Lower Brush Strip33
  - Glass Leaves33
- Install Leaves33
- Preparing the External Carriages34
- Telescopic Profile Assembly35
- Plate on Telescopic Profile36
- Preparing External Carriages36
- Steel Cable Fixing38
- Adjust Leaves and Carriages39
10 Install Glass Leaves40
- Mount the Sweepers42
11 Assemble the Belt, Casing and Accessories43
- Mount the Belt43
  - Adjust the Belt44
- Belt Tensioning45
- Belt Tensioning (Measurements in45
12 Electronic Installation51
- Electronics Module51
  - Electronic Board E1400 RD51
- LED on the Board52
13 Commissioning63
- Preliminary Checks Prior to Commissioning63
- System Power Supply and SETUP63
  - Checks Following SETUP63
  - Saving the Configuration63
- Basic / Advanced Programming64
14 System Functionality/Configurations68
- Operating Mode68
- Inputs Configuration69
- Configuration of J22 Outputs71
- Obstacle Detection71
- Anti-Intrusion and PULL&GO71
- Function Energy Saving72
  - How to Activate Theenergy Saving72
- Function Low Energy in Closing72
- Cs Cf72
  - How to Set Low Energy on Closure72
- 3 Setting Max Speed in Low Energy72
15 Diagnostics and Procedures73
- Acoustic Signal73
- System Diagnostics: Alerts, Errors73
- 4 Statuses of the Automation73
  - Solution of Problems or Outages76
16 Operations on the Board77
- Setup77
  - How to Perform Setup from Board77
- Reset77
  - When Is Reset Necessary77
  - How to Perform RESET from Board77
- Restoring Factory Status77
  - When Is Restore Necessary77
  - How to Perform Restore77
- Update (UPLOAD)78
- Download78
- 2 BOOTLOADER Errors79
17 Lkevo80
- Selection MENU80
- Firmware Version81
18 Sdk Evo84
- Assembly and Testing84
- Switching on and Use84
- Home Page85
- Reset - Block/Release SDKEVO85
- Password85
- Selection MENU86
- Function MENU87
- Errors88
- AUX Errors88
19 Maintenance97
- Calculation Estimate of Cycles Performed97
  - Routine Maintenance97
  - Periodic Replacements97
- Maintenance Technician Safety98
- Replacements98
- Cleaning100
- Functional Checks100
20 Waste Disposal100
21 Annexes101
- Positions of Components on the Head Section101

Related product manuals

FAAC A1400 AIR RD

Preview: FAAC A1400 AIR

FAAC A140 AIR Series

Preview: FAAC 950N2

Preview: FAAC 950 N

Preview: FAAC 595

Preview: FAAC 950 BM

Preview: FAAC DAAB MT

Preview: FAAC S2500I CERNIERA

FAAC S2500I CERNIERA