Fluke Calibration 5322A

To Next Page

To Previous Page

Multifunction Electrical Tester Calibrator

Calibrate Insulation Resistance Testers

173

Fluke 5322A

Fluke 5322A R Multiplier

Front Back

iep051.eps

Figure 37. Connections to Bench Tester when using Resistance Multiplier Adapter

Main Page

Table of Contents5
Introduction9
Safety Information10
- Warnings10
- Symbols12
Contact Fluke Calibration13
Specifications13
Service Information13
Calibrator Functions14
- Function Descriptions14
- Other Features16
Accessories16
- Included Accessories17
- Optional Accessories18
Unpack and Inspect the Product18
Power Considerations18
- Mains Power Cord19
- Mains Voltage19
- Ground the Product20
- Line Power and Fuse20
- Replace the Fuses20
- Select the Line Voltage21
Install the Product in an Equipment Rack21
Switch Power on21
Operation Rules23
Warm-Up Time23
Front-Panel Operation24
- Front-Panel Feature Descriptions24
- Rear-Panel Features28
- Display Features29
Control the Product31
- Select a Function31
- Help31
- Set the Output Signal Value32
- Readings34
- Connection/Disconnection of Output Terminals34
Calibrator Setup Menu35
- Set a General Setup Function35
Factory Settings39
Product Functions40
Set the Low Resistance Source Output40
- Output Selection40
Set the High Resistance Source Output43
- Output Selection44
Set the Ground Bond Resistance Output47
- Use the Ground Bond Resistance Mode48
- Use the Ground Bond Resistance Open Function49
Use the Loop and Line Impedance Function49
- Line and Loop Residual Impedance52
- Set the Compensation of Test Lead Resistance Value58
Use the Leakage Current Function58
- Passive Leakage Current59
- Differential Leakage Current60
- Active Leakage Current (5322A/VLC Only)61
- Substitute Leakage Current Mode63
Use the RCD Test Functions66
- RCD Trip Current Function for Installation Testers66
  - Power Line Voltage69
  - Touch (Contact) Voltage69
- Trip Current Calculation70
- RCD Trip Time for Installation Testers71
  - Power Line Voltage73
  - Touch (Contact) Voltage73
- Output Terminals Reconnection76
- RCD Trip Time for Pats77
AC/DC Voltage Outputs (5322A/VLC Only)78
Measure with the Built-In Multimeter81
- Function Selection82
- Multimeter Input Selection84
- HIPOT LC Function84
- HIPOT Timer Function88
- Flash V (Voltage) Function89
- Flash LC (Leakage Current) Function90
Remote Operation91
Using the IEEE 488 Port for Remote Control91
- IEEE 488 Bus Restrictions91
- Set up the IEEE 488 Port92
Use the USB Port for Remote Control92
- Set up the USB Port93
- Exceptions for USB Remote Control94
5320A Remote Emulation94
Remote Interface Factory Settings94
Command Syntax Information95
- Parameter Syntax Rules95
- Terminators96
- Description of Abbreviations96
- Numeric Output Format97
Supported SCPI Commands97
- SCPI Command Summary98
- System Command Summary110
- Status Command Summary110
- Common Command Summary111
- SCPI Command Details112
  - Using the Output Commands112
  - Using the Source Commands112
- Using System Commands153
- Status Subsystem155
- IEEE 488.2 Common Commands157
- Standard Status Data Structures159
- IEEE 488 Interface Configuration163
Operator Maintenance164
Clean the Ground Bond Resistance and Loop/Line Impedance Relays165
Access the Fuses166
- Line-Power Fuse166
- Measurement Input Fuses166
Clean the Air Filter167
Clean the Exterior168
Product Error Messages169
What to Do in Case of Product Failure172
DUT Calibration Examples172
- Calibrate Continuity Testers173
Calibrate Earth Resistance Testers174
Calibrate Insulation Resistance Testers175
- Calibrate Hand Crank Insulation Testers with the 5 Kv High Resistance Option178
- Calibrate Insulation Resistance Testers with the Resistance Multiplier179
- Calibrate Ground Bond Resistance Testers187
Calibrate Ground Bond Resistance Function in HIPOT Testers189
Calibrate Line Impedance Testers190
Calibrate Loop Impedance Testers192
Calibrate Leakage Current Testers193
- Passive, Differential, and Substitute Leakage Current Calibration193
Calibrate Residual Current Device (RCD) in Installation Testers195
- Calibrate RCD Trip Time195
- Calibrate RCD Trip Current199
Calibrate Residual Current Device (RCD) in Pats (Portable Appliance Tester)200
Calibrate AC and DC Voltage (5322A/VLC Only)202
Calibrate Load Test for Appliance Testers205
Perform Flash Class I and Flash Class II Tests on (PAT) Portable Appliance Testers207
Calibrate Hipots211
- Measure High Voltage with the HV Input211
- Measure High Voltage with the 10 Kv Divider Probe212
- Measure High Voltage with the 80K-40 High Voltage Probe213
- Measure Leakage Current with the 5322A-LOAD214

Fluke Calibration 5322A - Page 181

Table of Contents

Other manuals for Fluke Calibration 5322A

Related product manuals