GE PANDA Service Manual

TOC-4 Service Manual
5.5.3 SpO2 Connector/Flex Circuit Replacement (Figure 5-10 or Figure 5-11
as appropriate) ...............................................................................................................................................5-17
5.5.4 Scale Connector Replacement (Figure 5-10) (Bedded Models Only)............................5-18
5.5.5 Patient Probe Connector Replacement (Figure 5-10 or Figure 5-11
as appropriate) ...............................................................................................................................................5-18
5.5.6 Probe Panel Upper Housing Replacement ..............................................................................5-19
5.6 Appearance Strip Replacement...............................................................................................................5-20
5.7 Lower Unit Repairs (Bedded and Freestanding Models)...............................................................5-21
5.7.1 Removing the Bed (Figure 5-13) (Bedded Models Only).....................................................5-21
5.7.2 Elevating Column Replacement (Figure 5-14) (Bedded Models Only) .........................5-21
5.7.3 Foot Switches (Figure 5-14) (Bedded Models Only)..............................................................5-21
5.7.4 Caster Replacement (Figure 5-14) (Bedded and Freestanding Models).....................5-22
5.7.5 Adjusting Bed Height Using Manual Elevating Column (Bedded Model Only).........5-24
5.7.6 Base and Rail Mounting Block Replacement (Figure 5-14)
(Freestanding Models Only) ......................................................................................................................5-25
Chapter 6: Illustrated Parts ........................................................................................6-1
6.1 Heater Housing...................................................................................................................................................6-2
6.2 Electronics Enclosure .......................................................................................................................................6-4
6.3 Probe Panel Housing........................................................................................................................................6-8
6.3.1 Probe Panel Housing (with Masimo SET 1 SpO2 Jack)...........................................................6-8
6.3.2 Probe Panel Housing (with Masimo SET 2 or Nellcor SpO2 Jack).....................................6-9
6.4 Base Assembly (Bedded Models Only)...................................................................................................6-10
6.4.1 Elevating Column Special Instructions ......................................................................................6-10
6.5 Bed Assembly (Bedded Models Only).....................................................................................................6-13
6.6 Storage Options (Bedded Models Only) ................................................................................................6-16
6.7 Freestanding Model Parts...........................................................................................................................6-18
6.8 Wall Mount Model Parts...............................................................................................................................6-19
6.8.1 FRU Wall Mount Warmer Bumper Kit (2063179-001) Content.......................................6-20
6.8.2 FRU Wall Mount Warmer Bracket Kit (Language-Specific) Content ............................6-20
6.9 Harness List .......................................................................................................................................................6-21
6.10 Options..............................................................................................................................................................6-22
6.10.1 Optional Equipment.........................................................................................................................6-22
6.10.2 Replacement and Additional Parts...........................................................................................6-23
6.10.3 SpO2 Upgrade Kits ...........................................................................................................................6-24
6.10.4 Giraffe Scale Parts ............................................................................................................................6-26
6.10.5 Panda Scale Parts.............................................................................................................................6-26
6.10.6 Power Cords ........................................................................................................................................6-26
6.11 Labels.................................................................................................................................................................6-27
6.11.1 Labels on the Back of Giraffe Warmers or Panda iRes Warmers...............................6-27
6.11.2 Heater Grille Accessory Warning Label Set (Bedded Models)......................................6-28
6.11.3 Labels on Probe Panel Housing..................................................................................................6-29

GE PANDA Specifications

General

Type	Infant Warmer
Manufacturer	GE Healthcare
Control Modes	Manual, Servo
Integrated Scale	Yes
SpO2 Monitoring	Optional
Bed Tilt	Yes
Heater Type	Ceramic
Alarms	Power Failure
Power Requirements	100-240 VAC, 50/60 Hz
Model	PANDA
Resuscitation Options	Optional
Skin Temperature Probe Accuracy	±0.3°C