HP A5120 EI Series Configuration Guide

166
[ProviderA-GigabitEthernet1/0/1] quit
 Configure GigabitEthernet 1/0/2
# Configure GigabitEthernet 1/0/2 as a hybrid port to permit frames of VLAN 1000 to pass through,
and configure GigabitEthernet 1/0/2 to send packets of VLAN 1000 with tag removed.
[ProviderA] interface gigabitethernet 1/0/2
[ProviderA-GigabitEthernet1/0/2] port link-type hybrid
[ProviderA-GigabitEthernet1/0/2] port hybrid vlan 1000 untagged
# Tag CVLAN 10 frames with SVLAN 1000.
[ProviderA-GigabitEthernet1/0/2] qinq vid 1000
[ProviderA-GigabitEthernet1/0/2-vid-1000] raw-vlan-id inbound 10
[ProviderA-GigabitEthernet1/0/2-vid-1000] quit
[ProviderA-GigabitEthernet1/0/2] quit
 Configure GigabitEthernet 1/0/3
# Configure GigabitEthernet 1/0/3 as a trunk port to permit frames of VLAN 1000 and VLAN 2000 to
pass through.
[ProviderA] interface gigabitethernet 1/0/3
[ProviderA-GigabitEthernet1/0/3] port link-type trunk
[Sysname-GigabitEthernet1/0/3] port trunk permit vlan 1000 2000
# Set the TPID value in the outer tag to 0x8200.
[ProviderA-GigabitEthernet1/0/3] quit
[ProviderA] qinq ethernet-type 8200
2. Configure Provider B.
 Configure GigabitEthernet 1/0/1
# Configure GigabitEthernet 1/0/1 as a trunk port to permit frames of VLAN 1000 and VLAN 2000 to
pass through.
<ProviderB> system-view
[ProviderB] interface gigabitethernet 1/0/1
[ProviderB-GigabitEthernet1/0/1] port link-type trunk
[ProviderB-GigabitEthernet1/0/1] port trunk permit vlan 1000 2000
 Configure GigabitEthernet 1/0/2
# Configure GigabitEthernet 1/0/2 as a hybrid port to permit frames of VLAN 2000 to pass through,
and configure GigabitEthernet 1/0/2 to send packets of VLAN 2000 with tag removed.
[ProviderB] interface gigabitethernet 1/0/2
[ProviderB-GigabitEthernet1/0/2] port link-type hybrid
[ProviderB-GigabitEthernet1/0/2] port hybrid vlan 2000 untagged
# Tag CVLAN 20 frames with SVLAN 2000.
[ProviderB-GigabitEthernet1/0/2] qinq vid 2000
[ProviderB-GigabitEthernet1/0/2-vid-2000] raw-vlan-id inbound 20
# Set the TPID value in the outer tag to 0x8200.
[ProviderA-GigabitEthernet1/0/3] quit
[ProviderA] qinq ethernet-type 8200
3. Configure third-party devices.

HP A5120 EI Series Specifications

General

Uplink Ports	4 x SFP
Stacking	No
Management	CLI, Web, SNMP
Routing Protocols	RIP, OSPF
Power Supply	AC
MAC Address Table Size	16K
Dimensions	440 x 430 x 44 mm
Operating Temperature	0°C to 45°C
Operating Humidity	10% to 90% non-condensing
Model	HP A5120-24G EI Switch (JG234A)
VLANs	4094