Huawei Quidway S6700 series User Manual

Configuration Roadmap
The configuration roadmap is as follows:
1. Create VRRP group 1 and VRRP group 2 on VLANIF 100 of Switch A. Ensure that Switch
A is the master device in VRRP group 1 and the backup device in VRRP group 2.
2. Create VRRP group 1 and VRRP group 2 on VLANIF 100 of Switch B. Ensure that Switch
B is the backup device in VRRP group 1 and the master device in VRRP group 1.
Data Preparation
To complete the configuration, you need the following data:
l IPv6 addresses of the interfaces
l IDs and virtual IPv6 addresses of the VRRP groups
l Priorities of the switches in each VRRP group
Procedure
Step 1 Configure IP addresses for the interfaces. The configuration procedure is not mentioned here.
Step 2 Configure OSPFv3 on Switch A, Switch B, and Switch C so that they can communicate with
each other. The configuration procedure is not mentioned here.
Step 3 Configure the hosts.
Set the default gateway address of Host A to 2000::10, which is the virtual IPv6 address of VRRP
group 1. Set the default gateway address of Host B to 2000::60, which is the virtual IPv6 address
of VRRP group 2. Set the default gateway address of Host C to 2003::2.
Step 4 Configure VRRP6 groups.
# Create VRRP group 1 and VRRP group 2 on VLANIF 100 of Switch A. Set the priority of
Switch A in VRRP group 1 to 120 so that Switch A becomes the master device in VRRP group
1. Use the default priority of Switch A in VRRP group 2 so that Switch A becomes the backup
device in VRRP group 2.
<Quidway> system-view
[Quidway] sysname SwitchA
[SwitchA] interface vlanif100
[SwitchA-Vlanif100] vrrp6 vrid 1 virtual-ip FE80::1 link-local
[SwitchA-Vlanif100] vrrp6 vrid 1 virtual-ip 2000::100
[SwitchA-Vlanif100] vrrp6 vrid 1 priority 120
[SwitchA-Vlanif100] vrrp6 vrid 2 virtual-ip FE80::2 link-local
[SwitchA-Vlanif100] vrrp6 vrid 2 virtual-ip 2000::60
[SwitchA-Vlanif100] quit
# Create VRRP group 1 and VRRP group 2 on VLANIF 100 of Switch B. Use the priority of
Switch B in VRRP group 1 to 120 so that Switch B becomes the backup device in VRRP group
1. Set the priority of Switch B in VRRP group 2 to 120 so that Switch B becomes the master
device in VRRP group 2.
<Quidway> system-view
[Quidway] sysname SwitchB
[SwitchB] interface vlanif 100
[SwitchB-Vlanif100] vrrp6 vrid 1 virtual-ip FE80::1 link-local
[SwitchB-Vlanif100] vrrp6 vrid 1 virtual-ip 2000::100
[SwitchB-Vlanif100] vrrp6 vrid 2 virtual-ip FE80::2 link-local
[SwitchB-Vlanif100] vrrp6 vrid 2 virtual-ip 2000::60
Quidway S6700 Series Ethernet Switches
Configuration Guide - Reliability 6 VRRP and VRRP6 Configuration
Issue 01 (2011-07-15) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
268

Huawei Quidway S6700 series Specifications

General

Brand	Huawei
Model	Quidway S6700 series
Category	Network Router
Language	English