The configurations of Switch B and Switch C are similar to the configuration of Switch A. The
detailed configurations are omitted here.
Step 2 Create an RRPP domain and the control VLAN.
# On the master node of ring 1, namely Switch A, create RRPP domain 1 and configure VLAN
20 as the main control VLAN.
[SwitchA] rrpp domain 1
[SwitchA-rrpp-domain-region1] control-vlan 20
[SwitchA-rrpp-domain-region1] quit
# On the transit node of ring 1, namely Switch B, create RRPP domain 1 and configure VLAN
20 as the main control VLAN.
<Quidway> system-view
[Quidway] sysname SwitchB
[SwitchB] rrpp domain 1
[SwitchB-rrpp-domain-region1] control-vlan 20
[SwitchB-rrpp-domain-region1] quit
# On the master node of ring 1, namely SwitchC, create RRPP domain 1 and configure VLAN
20 as the main control VLAN.
<Quidway> system-view
[Quidway] sysname SwitchC
[SwitchC] rrpp domain 1
[SwitchC-rrpp-domain-region1] control-vlan 20
[SwitchC-rrpp-domain-region1] quit
Step 3 Configure the interfaces to be added to the RRPP ring as trunk interfaces, allow VLANs 100 to
300 on the interfaces, and disable STP on the interfaces.
# Configure Switch A.
[SwitchA] interface xgigabitethernet 0/0/1
[SwitchA-XGigabitEthernet0/0/1] port link-type trunk
[SwitchA-XGigabitEthernet0/0/1] port trunk allow-pass vlan 100 to 300
[SwitchA-XGigabitEthernet0/0/1] stp disable
[SwitchA-XGigabitEthernet0/0/1] quit
[SwitchA] interface xgigabitethernet 0/0/2
[SwitchA-XGigabitEthernet0/0/2] port link-type trunk
[SwitchA-XGigabitEthernet0/0/2] port trunk allow-pass vlan 100 to 300
[SwitchA-XGigabitEthernet0/0/2] stp disable
[SwitchA-XGigabitEthernet0/0/2] quit
# Configure Switch B.
[SwitchB] interface gigabitethernet 0/0/1
[SwitchB-XGigabitEthernet0/0/1] port link-type trunk
[SwitchB-XGigabitEthernet0/0/1] port trunk allow-pass vlan 100 to 300
[SwitchB-XGigabitEthernet0/0/1] stp disable
[SwitchB-XGigabitEthernet0/0/1] quit
[SwitchB] interface xgigabitethernet 0/0/2
[SwitchB-XGigabitEthernet0/0/2] port link-type trunk
[SwitchB-XGigabitEthernet0/0/2] port trunk allow-pass vlan 100 to 300
[SwitchB-XGigabitEthernet0/0/2] stp disable
[SwitchB-XGigabitEthernet0/0/2] quit
# Configure Switch C.
[SwitchC] interface gigabitethernet 0/0/1
[SwitchC-XGigabitEthernet0/0/1] port link-type trunk
[SwitchC-XGigabitEthernet0/0/1] port trunk allow-pass vlan 100 to 300
[SwitchC-XGigabitEthernet0/0/1] stp disable
[SwitchC-XGigabitEthernet0/0/1] quit
[SwitchC] interface xgigabitethernet 0/0/2
[SwitchC-XGigabitEthernet0/0/2] port link-type trunk
Quidway S6700 Series Ethernet Switches
Configuration Guide - Reliability 3 RRPP Configuration
Issue 01 (2011-07-15) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
75
To Next Page
Loading...
Need help?
General
