# On Switch C, configure domain 1. Then configure VLAN 10 as the main control VLAN and
instance 1 as the protected instance of domain 1.
[SwitchC] rrpp enable
[SwitchC] rrpp domain 1
[SwitchC-rrpp-domain-region1] control-vlan 10
[SwitchC-rrpp-domain-region1] protected-vlan reference-instance 1
[SwitchC-rrpp-domain-region1] quit
# Disable STP on the interfaces to be added to the RRPP rings, configure the interfaces as trunk
interfaces, and configure the interfaces to allow service packets of VLAN 2 to VLAN 9 to pass
through.
[SwitchC] interface xgigabitethernet 0/0/1
[SwitchC-XGigabitEthernet0/0/1] port link-type trunk
[SwitchC-XGigabitEthernet0/0/1] port trunk allow-pass vlan 2 to 9
[SwitchC-XGigabitEthernet0/0/1] stp disable
[SwitchC-XGigabitEthernet0/0/1] quit
[SwitchC] interface xgigabitethernet 0/0/2
[SwitchC-XGigabitEthernet0/0/2] port link-type trunk
[SwitchC-XGigabitEthernet0/0/2] port trunk allow-pass vlan 2 to 9
[SwitchC-XGigabitEthernet0/0/2] stp disable
[SwitchC-XGigabitEthernet0/0/2] quit
# Configure the primary interface and secondary interface of the master node on the RRPP
subring.
[SwitchC] rrpp domain 1
[SwitchC-rrpp-domain-region1] ring 2 node-mode master primary-port
xgigabitethernet 0/0/1 secondary-port xgigabitethernet 0/0/2 level 1
[SwitchC-rrpp-domain-region1] ring 2 enable
[SwitchC-rrpp-domain-region1] quit
Step 3 Configure Switch A as the transit node of the major ring and the edge transit node of the subring.
# Create data VLANs 2 to 9 on Switch A.
<Quidway> system-view
[Quidway] sysname SwitchA
[SwitchA] vlan batch 2 to 9
Configure instance 1, and map it to the VLANs allowed by the RRPP interfaces and protected
VLANs.
[SwitchA] stp region-configuration
[SwitchA-mst-region] instance 1 vlan 2 to 11
[SwitchA-mst-region] active region-configuration
[SwitchA-mst-region] quit
# On SwitchA, configure domain 1. Then configure VLAN 10 as the main control VLAN and
instance 1 as the protected instance of domain 1.
[SwitchA] rrpp enable
[SwitchA] rrpp domain 1
[SwitchA-rrpp-domain-region1] control-vlan 10
[SwitchA-rrpp-domain-region1] protected-vlan reference-instance 1
[SwitchA-rrpp-domain-region1] quit
# Disable STP on the interfaces to be added to the RRPP rings, configure the interfaces as trunk
interfaces, and configure the interfaces to allow service packets of VLAN 2 to VLAN 9 to pass
through.
[SwitchA] interface xgigabitethernet 0/0/1
[SwitchA-XGigabitEthernet0/0/1] port link-type trunk
[SwitchA-XGigabitEthernet0/0/1] port trunk allow-pass vlan 2 to 9
[SwitchA-XGigabitEthernet0/0/1] stp disable
[SwitchA-XGigabitEthernet0/0/1] quit
Quidway S6700 Series Ethernet Switches
Configuration Guide - Reliability 3 RRPP Configuration
Issue 01 (2011-07-15) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
81
To Next Page
Loading...
