What to do if the Huawei UPS rectifier is not normal?
If the Huawei UPS rectifier is not working properly, there are a couple of things to check. First, determine if the mains voltage is outside the normal range (above 280 V or below 80 V). If it is, you should contact your electric power company. If the mains voltage is within the limits, try replacing the power module.
What to do if the ATS is not normal in Huawei UPS?
If the ATS (Automatic Transfer Switch) in your Huawei UPS system isn't working correctly, it could be due to an incorrect input three-phase sequence. To fix this, power off the ATS and check the phase sequence.
How to fix Huawei UPS5000-E UPS when it works in bypass mode?
If your Huawei UPS stays in bypass mode and doesn't switch to inverter mode, it might be because the bypass transfer times have reached their upper limit. To resolve this, clear the bypass transfer times on the LCD.
What to do if the bypass is not normal in Huawei UPS?
If the bypass function on your Huawei UPS is not working correctly, it could be due to a damaged bypass thyristor, requiring you to replace the bypass module. Alternatively, the bypass module might be experiencing overtemperature, in which case you should reduce the load or improve ventilation.
Why does the charger generate an alarm in Huawei UPS5000-E UPS?
If your Huawei UPS charger is alarming, it could be due to a few reasons. The charger might have failed or be experiencing overcurrent. In both cases, replace the power module. Also, the charger could be experiencing undervoltage. In this case, check if the configured number of batteries is correct. If the value is correct but the alarm persists, replace the power module.
Why does the charger generate an alarm in Huawei Power Supply?
The charger may be generating an alarm because the charger itself has failed. In this case, replace the power module. Also, check whether the configured number of batteries is correct; if the value is correct but the alarm persists, replace the power module.
Why Huawei UPS5000-E UPS works in bypass mode and does not transfer to inverter mode?
If your Huawei UPS works in bypass mode and does not transfer to inverter mode, set the UPS working mode to ECO mode or clear the bypass transfer times on the LCD.
What to do if the charger generates an alarm in Huawei UPS?
If the charger in your Huawei UPS generates an alarm, it could be due to a charger failure. In this case, replace the power module. Also, check whether the configured number of batteries is correct. If the value is correct but the alarm persists, replace the power module.
How to fix an abnormal rectifier in Huawei UPS?
If the rectifier in your Huawei UPS is abnormal, check whether the mains voltage exceeds the upper threshold of 150 V or is less than the lower threshold of 80 V. If it does, contact the electric power company. If the mains voltage is within the normal range, consider replacing the power module.
Why is the bypass abnormal in my Huawei UPS5000-E UPS?
If the bypass in your Huawei UPS is abnormal, it could be due to a damaged bypass thyristor, which requires replacing the bypass module. Also, consider reducing the load and improving ventilation to resolve the issue.
General| Model | UPS5000-E Series |
|---|---|
| Output Frequency | 50/60Hz |
| Topology | Double Conversion |
| Operating Temperature | 0°C to 40°C |
| Relative Humidity | 0% to 95% (non-condensing) |
| Cooling Method | Forced Air Cooling |
| Type | Online UPS |
| Power Capacity | 10kVA to 800kVA |
| Output Power | 10kW to 800kW |
| Efficiency (AC-AC) | Up to 96% |
| Battery Type | Lithium-ion |
| Battery Voltage | 192V |
| Communication Interface | SNMP, USB, Dry Contact |
| Dimensions (W x D x H) | Varies by model |
| Weight | Varies by model |
| Parallel Capability | Up to 8 units |
| Certifications | CE, UL |
| Input Voltage | 380/400/415 VAC (3-phase, 3-wire + PE) or (3-phase, 4-wire + PE) |
| Output Voltage | 380/400/415 VAC (3-phase, 3-wire + PE) or (3-phase, 4-wire + PE) |
General safety precautions, responsibilities, and user guidelines for equipment operation and maintenance.
Specifies the necessary qualifications, training, and roles for personnel involved in installation and operation.
Covers essential electrical safety practices, including grounding and handling of electrical components.
Details the environmental conditions, clearances, and location requirements for UPS installation.
Safety procedures related to mechanical operations like hoisting, ladder usage, and handling heavy objects.
Precautions to be taken during the UPS operation and in specific environments.
Critical safety guidelines for handling, installing, and maintaining batteries to prevent hazards.
Additional safety considerations and precautions for miscellaneous operational aspects.
Explains the UPS model naming convention, configurations, and supported capacities.
Describes the UPS conceptual diagram and its different operating modes.
Details the physical structure and main components of the UPS system.
Outlines common UPS system configurations like Single, Parallel, and Dual-bus setups.
Lists and briefly describes optional components that can be added to the UPS.
Covers site selection, tools, power cable preparation, unpacking, and initial checks before installation.
Step-by-step guide for installing the UPS cabinet, batteries, and optional components.
Procedures for connecting multiple UPS units in parallel or dual-bus configurations.
Provides a checklist and acceptance criteria to ensure the UPS installation is correct.
Explains the operation and features of the UPS's Liquid Crystal Display (LCD) interface.
Guides users on accessing and navigating the Web-based User Interface for UPS management.
Instructions for using the older version of the Web User Interface for UPS management.
Detailed procedures for powering on the UPS and performing initial startup, including password obtaining.
Steps for safely shutting down and powering off the UPS system and its components.
Procedure to start the UPS using battery power when mains power is unavailable.
Instructions on how to manually transfer the UPS operation to bypass mode for maintenance.
Configuration steps for enabling the Economy Control Operation (ECO) mode for energy savings.
Guides on performing battery tests such as Forced Equalized Charging, Shallow Discharge, and Capacity Test.
Steps to safely move the UPS from normal operation to maintenance bypass mode.
Procedure to return the UPS from maintenance bypass mode back to normal operation.
How to initiate an Emergency Power Off (EPO) using the external switch or dry contact.
Steps to clear the EPO alarm and reset the UPS after an EPO event has occurred.
Instructions on exporting various types of data like alarms, logs, and configuration files from the UPS.
How to configure the UPS to enter hibernation mode for power saving and extending component lifespan.
General guidelines and schedules for performing regular maintenance tasks on the UPS system.
Procedures and safety precautions for maintaining UPS batteries on a monthly, quarterly, and annual basis.
Provides a list of common UPS faults, symptoms, possible causes, and recommended solutions.
Details physical dimensions, weight, cabling modes, and protection levels for different UPS models.
Specifications for internal switches like maintenance bypass, mains input, bypass input, and output switches.
Specifies the acceptable operating and storage environmental conditions for the UPS.
Lists the safety standards and Electromagnetic Compatibility (EMC) regulations the UPS complies with.
Electrical parameters related to the UPS mains input, including voltage, frequency, and power factor.
Electrical parameters for the bypass input, including voltage, frequency, and input mode.
Details battery voltage requirements, management, and charging specifications for different UPS capacities.
Electrical parameters for the UPS output, including voltage, frequency, overload capability, and transfer time.
System-level electrical specifications such as redundancy design and ECO mode support in parallel systems.
Describes the procedure for short-circuiting the input N and PE for TN-C system applications.
A comprehensive list of UPS alarms, including ID, name, severity, cause, and recommended solutions.
A glossary of acronyms and abbreviations used throughout the manual.
To Next Page
