EasyManuals Logo

jcb 19C-1E User Manual

jcb 19C-1E
180 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #34 background imageLoading...
Page #34 background image
Operation
Operating Safety
Roll Over Protection
If the machine starts to roll over, you can be crushed if you try to leave the cab. If the machine starts to roll
over, do not try and jump from the cab. Stay in the cab, with your seat belt fastened.
Confined Areas
Pay extra attention to proximity hazards when operating in confined areas. Proximity hazards include buildings,
traffic and bystanders.
Safe Working Loads
Overloading the machine can damage it and make it unstable. Study the specifications in the Operator's Manual
before using the machine.
Lightning
If you are inside the machine during a lightning storm stay in the machine until the storm has passed. If you
are outside of the machine during a lightning storm stay away from the machine until the storm has passed.
Do not attempt to mount or enter the machine.
If the machine is struck by lightning do not use the machine until it has been checked for damage and
malfunction by trained personnel.
Worksite Safety
WARNING You or others can be killed or seriously injured if you do unfamiliar operations without first
practising them. Practise away from the worksite on a clear area. Keep other people away. Do not perform
new operations until you are sure you can do them safely.
WARNING There could be dangerous materials such as asbestos, poisonous chemicals or other harmful
substances buried on the site. If you uncover any containers or you see any signs of toxic waste, stop the
machine and advise the site manager immediately.
WARNING Before you start using the machine, check with your local gas company if there are any buried
gas pipes on the site.
If there are buried gas pipes we recommend that you ask the gas company for any specific advice regarding
the way you must work on the site.
Some modern gas pipes cannot be detected by metal detectors, so it is essential that an accurate map of
buried gas pipes is obtained before any excavation work commences.
Hand dig trial holes to obtain precise pipe locations. Any cast iron pipes found must be assumed to be gas
pipes until contrary evidence is obtained.
Older gas pipes can be damaged by heavy vehicles driving over the ground above them.
Leaking gas is highly explosive.
If a gas leak is suspected, contact the local gas company immediately and warn all personnel on the site.
Ban smoking, make sure that all naked lights are extinguished and switch off any engines which may be
running.
You are strongly advised to make sure that the safety arrangements on site comply with the local laws and
regulations concerning work near buried gas pipes.
CAUTION Before you start using the machine, check with your local public water supplier if there are buried
pipes and drains on the site. If there are, obtain a map of their locations and follow the advice given by
the water supplier.
You are strongly advised to make sure that the safety arrangements on site comply with the local laws and
regulations concerning work near buried pipes and drains.
CAUTION If you cut through a fibre optic cable, Do not look into the end of it, your eyes could be permanently
damaged.
An applicable worksite organisation is required in order to minimise hazards that are caused by restricted
visibility. The worksite organisation is a collection of rules and procedures that coordinates the machines and
people that work together in the same area. Examples of worksite organisation include:
Restricted areas
24 9831/8250-4 24
JCB © Admin Pimteam - 23/06/2021 05:32.

Table of Contents

Other manuals for jcb 19C-1E

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the jcb 19C-1E and is the answer not in the manual?

jcb 19C-1E Specifications

General IconGeneral
Battery TypeManganese laminated Lithium-ion
Battery Rated Capacity14.8 kWh (3 Pack) 19.8 kWh (4 Pack)
ChargingOn-board charger with direct connection from AC mains power supply
Charging Time110V – 12 hrs 230V – 8 hrs
Fast Charging (Optional)Off-board charger, with connection to 415V 3-Phase supply Charging time <2 hrs
System Voltage48V
Motor TypeAC permanent magnet
Motor Power7 kW continuous 20kW peak
Operating ModesL – 1200rpm G – 1600rpm H – 1800rpm Auto Kick Up – 2300rpm, 2 speed tracking only
Thermal LimitationsOperation: -10oC to +46oC Charging: -10oC to +40oC

Related product manuals