Krone 1022623 - Page 4

Contents
4
Comprima F 155
Original Operating Instructions 150001049_01_en
5.1.2 Lubricating greases ................................................................................................................... 44
6 Initial operation ........................................................................................................................ 45
6.1 Scope of delivery ....................................................................................................................... 45
6.2 Mounting hose and cable support.............................................................................................. 46
6.3 Preparing the brake disc of the wrapping material brake .......................................................... 46
6.4 Checking/adapting the tyre pressure ......................................................................................... 46
6.5 Adjusting the drawbar height ..................................................................................................... 47
6.6 Universal shaft ........................................................................................................................... 49
6.6.1 Adjusting the length of the universal shaft ................................................................................. 49
6.6.2 Mounting protective cap of universal shaft ................................................................................ 50
6.6.3 Mounting universal shaft bracket ............................................................................................... 50
6.6.4 Mounting the universal shaft on the machine ............................................................................ 51
6.7 Removing the tensioning device................................................................................................ 51
7 Commissioning........................................................................................................................ 53
7.1 Connecting machine to tractor................................................................................................... 53
7.2 Mounting the universal shaft on the tractor................................................................................ 54
7.3 Connecting hydraulic hoses....................................................................................................... 55
7.4 Connecting hydraulic brake (export).......................................................................................... 56
7.5 Coupling the hydraulic auxiliary brake ....................................................................................... 57
7.6 Connecting/disconnecting compressed air connections for the compressed air brake ............. 57
7.7 Adjusting drawbar eye ............................................................................................................... 58
7.8 Connecting the KRONE ALPHA operation unit ......................................................................... 58
7.9 Connecting KRONE terminal DS 500 ........................................................................................ 59
7.10 Connecting KRONE BETA II terminal........................................................................................ 61
7.11 Connecting the KRONE ISOBUS terminal (CCI800, CCI 1200)............................................... 63
7.12 Connecting foreign ISOBUS terminal ........................................................................................ 65
7.13 Connecting the camera to the KRONE ISOBUS terminal CCI 800 or CCI 1200....................... 67
7.14 Connecting the road lighting ...................................................................................................... 67
7.15 Mounting safety chain................................................................................................................ 68
8 Operation.................................................................................................................................. 69
8.1 Preparation before baling .......................................................................................................... 69
8.2 Filling the bale chamber............................................................................................................. 69
8.3 Improving bale chamber filling ................................................................................................... 71
8.3.1 Reducing the pressure on the side walls of the bale chamber .................................................. 71
8.3.2 Mounting additional driver guide rails on the starter roller ......................................................... 71
8.3.3 Mounting additional deflector sheets in the tailgate................................................................... 72
8.4 Completing the baling process, starting tying cycle and ejecting round bales........................... 73
8.5 Operating the support jack......................................................................................................... 73
8.6 Using the stop cock of the tailgate............................................................................................. 75
8.7 Releasing/applying the parking brake........................................................................................ 76
8.8 Fitting wheel chocks .................................................................................................................. 77
8.9 Removing/mounting the safety device which prevents unauthorised use ................................. 78
8.10 Operating brake force regulator................................................................................................. 78
8.11 Operating the bale counter ........................................................................................................ 79
8.12 Pick-up....................................................................................................................................... 79
8.12.1 Bringing the pick-up to transport/working position ..................................................................... 79
8.12.2 Setting the pick-up working height............................................................................................. 80
8.12.3 Adjusting the bearing pressure relief for the pick-up ................................................................. 81
8.13 Crop press roller unit ................................................................................................................. 81
8.13.1 Setting the crop press roller unit ................................................................................................ 82
8.13.2 Setting the baffle sheet on the crop press roller unit ................................................................. 82
8.13.3 Removing/mounting the baffle sheet on the crop press roller unit............................................. 83
8.14 Lifting/lowering the feeder rotor floor ......................................................................................... 84
8.15 Net wrapping.............................................................................................................................. 84
8.15.1 Inserting the net roll ................................................................................................................... 84
8.15.2 Insert net.................................................................................................................................... 86
8.16 Net and chamber film wrapping ................................................................................................. 87
8.16.1 Inserting a net or film roll ........................................................................................................... 87
8.16.2 Inserting the net or film .............................................................................................................. 88