Krone Big Pack 890 HS - Setting the Triggering Sensitivity

Settings
216
Pos: 32.109.21 /Übersc hriften/Übersc hriften 3/A-E/Ei nstellung der Auslöseempf indlichkeit @ 24\mod_1241 436809555_78.doc @ 244518
10.11.4 Setting the triggering sensitivity
Pos: 32.109.22 /BA/Ei nstellungen/Großpac kenpresse/Vari ables Füllsystem VFS/Ei nstellung der Auslösee mpfindlichkeit Bi ld HS Baureihe @ 63\mod_1299 737209712_78.doc @ 575205
Fig.157
Pos: 32.109.23 /BA/Ei nstellungen/Großpac kenpresse/Vari ables Füllsystem VFS/Ei nstellung der Auslösee mpfindlichkeit Al lgemein HS Baureihe @ 63\mod_1299827375507_78.doc @ 576478
The purpose of the spring (8) is to pre-tension the feeler rocker via the anvil (4) and the
threaded spindle (2) and move it back into the swivelled-in position after the fodder has been
pushed in. The anvil (4) must come up to touch the setting screw (3) for this to happen.
Pos: 32.109.24 /BA/Ei nstellungen/Großpac kenpresse/Vari ables Füllsystem VFS/Ei nstellung der Auslösee mpfindlichkeit Richtmaß @ 24\mod_1241437759 477_78.doc @ 244619
As a rough guide, the spring should be pre-tensioned to a length of C = 205 - 210 mm.
To do this:
• Loosen the screw connection (9) and retighten it after setting it to the dimension
Pos: 32.109.25 /BA/Ei nstellungen/Großpac kenpresse/Vari ables Füllsystem VFS/Ei nstellung der Auslösee mpfindlichkeit Feder spannung erhöhen @ 24\ mod_1241437762696_7 8.doc @ 244644
The spring tension should be increased if the bale channel chamber does not fill up sufficiently
to its full height.
Poorly filled out bale corners are generally the result of unfavorable swath shapes or driving to
one side.
Pos: 32.109.26 /BA/Ei nstellungen/Großpac kenpresse/Vari ables Füllsystem VFS/Ei nstellung der Auslösee mpfindlichkeit Feder spannung verri ngern @ 24\mod_1241437767165_7 8.doc @ 244669
The spring tension should be reduced as soon as the packer overload coupling is engaging
frequently.
If the spring tension is too high, the result may be blocking up the packer and thus reducing
throughput.
Pos: 32.109.27 /BA/Ei nstellungen/Großpac kenpresse/Vari ables Füllsystem VFS/Ei nstellung der Auslösee mpfindlichkeit Tastschwinge versetzen @ 24\ mod_1241438176446_78. doc @ 244694
Note
If the bale shape is still not satisfactory after tensioning the spring, the feeler rocker (1) should
be installed in a higher bore hole.
If the feeler rocker is too high, the result may be a block up of the packer, thus reducing
throughput.
• Loosen hexagonal head screw (3) on the feeler rocker (1)
• Swivel the feeler rocker (1) into the desired position (A, B or C) and fasten it in place with
the hexagonal head screw (3)
• Adjust the settings of the variable filling system (VFS) to the feeler rocker (refer to chapter
Setting the variable filling System VFS “Assembling the feeler rocker”)
Pos: 32.109.28 /BA/- ----Seitenumbruc h------ @ 0\mod_119617531 1226_0.doc @ 4165