kruss DSA100 - Page 56

To Next Page

To Previous Page

page 54 Mounting axes

2. Fix the table on the sample stage with the four hexagon socket screws supplied.

3. Slide the sample stage mount back into the holder. Retighten the two knurled

screws.

SPAC S PA C S PAC SPAC

Main Page

Default Chapter3
- Table of Contents3
1 General Information7
- General Safety Instructions7
- Intended Use7
- Procedure if Repairs Should be Necessary8
- Comprehensiveness of the Printed Version and the Electronic Manual9
- Note Concerning Images9
- Technical Customer Service9
2 Introduction10
3 DSA100 Overview12
4 Computer System13
- Mounting an IEEE-1394 Interface Board13
- Driver Installation14
5 Setting up23
- Opening the Transport Packing and Checking the Scope of Supply23
- Transport23
- Location and Ambient Conditions23
- Levelling the Instrument24
- Power Supply / Power Switch25
- Connecting the Computer25
  - Carrying out the Connection25
  - Port Assignment26
- Protective Glass27
- Connecting a Temperature Sensor28
6 Optical Components29
- Connecting the Camera29
- Assembling and Adjusting the Prism30
- Illumination / Aperture31
7 Mounting Axes33
- Order of the Axes and Height Compensation with Spacers33
- Mounting a Spacer34
  - Threads for Mounting Spacers and Axes34
  - Replacing an Axis with a Spacer34
- Mounting Axes35
- Connecting Software-Controlled Axes38
- Mounting a Rotating Table40
- Tilting Table PA322046
- PA3240 Internal Tilting Table49
8 Manual Single-Dosing Unit DS3200/320157
- Fitting a Disposable Syringe57
- Assembling the Dosing Unit to the DSA10058
- Adjusting the Dosing Unit59
9 Software-Controlled Single-Dosing Unit DS321060
- Mounting the Dosing Unit60
- Fitting the Syringe61
- Adjusting the Dosing Unit62
- Restricted Software Options63
10 Multi-Dosing Unit DS3226-322864
- Initialising the Syringe Drives64
- Inserting the Syringes65
- Adjusting the Dosing Unit68
11 Environmental Chambers TC30 and TC4070
- Safety Instructions70
- Temperature Range and Method of Temperature Control70
- Construction71
  - Front - Controls71
  - Rear - Connectors71
- TC30/40: Mounting on the DSA10072
- Connectors and Connections72
- Preparing the Measurement76
- Additional Components78
  - Base Plate Attachment for Flat Samples78
  - Heat Conducting Hood78
- TC40 Only: Setting and Reading off the Measuring Temperature80
12 Humidity Chamber HC1082
- Temperature Range and Method of Temperature Control82
- Notes for Use82
- Assembling the Interface Board82
- Mounting on the TC30/40 Environmental Chamber83
- Connectors and Connections85
  - Liquid and Gas Connections85
  - Power Supply / Communication87
- Filling / Filling Level87
- Fitting the Temperature Sensor88
- Covering the Needle Inlet88
Appendix89
I Computer Requirements89
- Exchanging Cameras92
- Iia) Assembly92
- Iib) Horizontal Alignment94
- Assembling an Interface Board for Software-Controlled Axes if Ordered Afterwards94
- Iiia) Safety Notes94
- Iiib) Procedure95
Mounting Steps for a Multi-Dosing Unit if Ordered Afterwards98
- Iva) Assembling the Syringe Driver Unit(S)98
- Ivb) Assembling the Syringe Revolver104
Addresses and Mounting of the Electronic Module EM3201107
- Va) Overview107
- Vb) Slots and Addresses108
- VC) Mounting109
Test Liquids for Multi-Dosing Unit DS3222-3228113
For DSA1 with DS3222-3228: Copying the DCM.ini File114
Warranty and Caveat Emptor114
Copyright and Right to Make Alterations114

kruss DSA100 - Page 56

Table of Contents

Related product manuals