MacDon FFT FD75 - Lowering Header

214325 v Revision A
5.1.2 Case IH 2300/2500 and 5088/6088/7088 Combines ..................................................................144
Engaging Auto Header Height Control (Case IH 2300) ..............................................................144
Calibrating Auto Header Height Control (AHHC) (Case IH 2300/2500 and 5088/6088/
7088) ........................................................................................................................145
Setting Sensitivity of Auto Header Height Control (Case IH 2300/2500 and 5088/6088/
7088) ........................................................................................................................146
5.1.3 Case IH 5130/6130/7130, 7010/8010, 7120/8120/9120, and 7230/8230/9230 Combines ..............148
Checking Voltage Range from Combine Cab (Case 8010) .........................................................148
Setting Header Controls (Case 8010).......................................................................................150
Checking Voltage Range from Combine Cab (Case IH 5130/6130/7130, 7010/8010;
7120/8120/9120; 7230/8230/9230)..............................................................................151
Calibrating Auto Header Height Control (Case IH 5130/6130/7130, 7010/8010;
7120/8120/9120; 7230/8230/9230)..............................................................................154
Calibrating Auto Header Height Control (Case Combines with Version 28.00 or Higher
Software)...................................................................................................................156
Setting Preset Cutting Height (Case 7010/8010, 7120/8120/9120, 7230/8230/9230) ...................158
5.1.4 Challenger 6 and 7 Series Combines ........................................................................................159
Checking Voltage Range from Combine Cab (Challenger 6 and 7 Series) ...................................159
Engaging Auto Header Height Control (Challenger 6 Series)......................................................161
Calibrating Auto Header Height Control (Challenger 6 Series)....................................................162
Adjusting Header Height (Challenger 6 Series) .........................................................................164
Adjusting Header Raise/Lower Rate (Challenger 6 Series) ........................................................164
Setting Sensitivity of Auto Header Height Control (Challenger 6 Series)......................................165
5.1.5 Gleaner R62/R72 Combines ....................................................................................................166
System Requirements (Gleaner R62/R72)................................................................................166
Calibrating Auto Header Height Control (Gleaner R62/R72) .......................................................167
Setting Sensitivity of Auto Header Height Control (Gleaner R62/R72 Series)...............................167
5.1.6 Gleaner R65/R66/R75/R76 and S Series Combines (Except S9 Series) ......................................170
Checking Voltage Range from Combine Cab (Gleaner R65/R66/R75/R76 and S Series) .............170
Engaging Auto Header Height Control (Gleaner R65/R66/R75/R76 and S Series) .. .....................171
Calibrating Auto Header Height Control (Gleaner R65/R66/R75/R76 and S Series) .....................172
Turning Accumulator Off (Gleaner R65/R66/R75/R76 and S Series)...........................................174
Adjusting Header Raise/Lower Rate (Gleaner R65/R66/R75/R76 and S Series)..........................174
Adjusting Ground Pressure (Gleaner R65/R66/R75/R76 and S Series).......................................175
Adjusting Sensitivity of Auto Header Height Control (Gleaner R65/R66/R75/R76 and
S Series) ...................................................................................................................176
Troubleshooting Alarms and Diagnostic Faults (Gleaner R65/R66/R75/R76 and
S Series) ...................................................................................................................177
5.1.7 Gleaner S9 Series Combines ...................................................................................................179
Setting up Header (Gleaner S9 Series) ....................................................................................179
Setting up Reel Settings (Gleaner S9 Series)............................................................................183
Setting up Automatic Header Controls (Gleaner S9 Series)........................................................185
Calibrating Header (Gleaner S9 Series) ...................................................................................187
Operating with a Gleaner S9 Series Combine ...........................................................................190
Header In-Field Settings .........................................................................................................192
5.1.8 John Deere 50 Series Combines ..............................................................................................193
Output Voltage Range.............................................................................................................193
Calibrating Auto Header Height ...............................................................................................197
Setting Sensitivity of Auto Header Height Control ......................................................................199
Adjusting Threshold for Drop Rate Valve ..................................................................................200
Operating Auto Header Height.................................................................................................201
Replacing Auto Header Height Control (AHHC) Sensor .............................................................203
TABLE OF CONTENTS