214325 vi Revision A
5.1.9 John Deere 60 Series Combines ..............................................................................................204
Checking Voltage Range from Combine Cab (John Deere 60 Series) .........................................204
Calibrating Auto Header Height Control (John Deere 60 Series).................................................206
Turning Accumulator Off (John Deere 60 Series) ......................................................................207
Setting Sensing Grain Header Height to 50 (John Deere 60 Series)............................................208
Setting Sensitivity of Auto Header Height Control (John Deere 60 Series) ...................................209
Adjusting Threshold for Drop Rate Valve (John Deere 60 Series) ...............................................210
5.1.10 John Deere 70 Series Combines ............................................................................................210
Checking Voltage Range from Combine Cab (John Deere 70 Series) .........................................210
Calibrating Feeder House Speed (John Deere 70 Series) ... .......................................................214
Calibrating Auto Header Height Control (John Deere 70 Series).................................................214
Setting Sensitivity of Auto Header Height Control (John Deere 70 Series) ...................................215
Adjusting Manual Header Raise/Lower Rate (John Deere 70 Series)..........................................216
5.1.11 John Deere S and T Series Combines.....................................................................................217
Checking Voltage Range from Combine Cab (John Deere S and T Series) .................................217
Calibrating Feeder House Fore/Aft Tilt Range (John Deere S and T Series) ................................220
Calibrating Auto Header Height Control (John Deere S and T Series) .........................................223
Setting Sensitivity of Auto Header Height Control (John Deere S and T Series) ...........................225
Adjusting Manual Header Raise/Lower Rate (John Deere S and T Series) ..................................226
Setting Preset Cutting Height (John Deere S and T Series)........................................................227
5.1.12 CLAAS 500 Series Combines.................................................................................................229
Auto Header Height Sensor Voltage Requirements ...................................................................229
Checking Sensor’s Output Voltage Range ................................................................................230
Calibrating Auto Header Height System ...................................................................................231
Setting Cutting Height (CLAAS 500 Series) ..............................................................................234
Setting Preset Cutting Height (CLAAS 500 Series) ....................................................................234
Setting Cutting Height Manually (CLAAS 500 Series) ................................................................235
Setting Sensitivity of Auto Header Height Control (CLAAS 500 Series) .......................................235
Adjusting Auto Reel Speed (CLAAS 500 Series) .......................................................................238
5.1.13 CLAAS 700 Series Combines.................................................................................................241
Auto Header Height Sensor Voltage Requirements ...................................................................241
Checking Sensor’s Output Voltage Range ................................................................................241
Calibrating Auto Header Height System ...................................................................................243
Setting Cutting Height (CLAAS 700 Series) ..............................................................................246
Setting Sensitivity of Auto Header Height Control (CLAAS 700 Series) .......................................246
Adjusting Auto Reel Speed (CLAAS 700 Series) .......................................................................248
5.1.14 New Holland Combines CX/CR Series (CR Series – Model Year 2014 and Earlier) ....................250
Checking Voltage Range from Combine Cab (New Holland) ......................................................250
Engaging Auto Header Height Control (New Holland CR/CX Series) ..........................................252
Calibrating Auto Header Height Control (New Holland CR/CX Series) ........................................253
Adjusting Header Raise Rate (New Holland CR/CX Series) .. .....................................................255
Setting Header Lower Rate to 50 (New Holland CR/CX Series) ..................................................256
Setting Sensitivity of Auto Header Height Control to 200 (New Holland CR/CX Series).................256
Setting Preset Cutting Height (New Holland CR/CX Series) .......................................................257
Configuring Reel Fore-Aft, Header Tilt, and Header Type (New Holland CR Series).....................258
5.1.15 New Holland Combines (CR Series – Model Year 2015 and Later) ............................................260
Engaging Auto Header Height Control (New Holland CR Series) ..
..............................................260
Checking Voltage Range from Combine Cab (New Holland CR Series) ......................................262
Calibrating Auto Header Height Control (New Holland CR Series) ..............................................265
Setting Auto Height (New Holland CR Series) ...........................................................................268
Setting Maximum Work Height (New Holland CR Series)...........................................................269
5.1.16 Sensor Operation ..................................................................................................................270
TABLE OF CONTENTS
To Next Page
Loading...
