Mitsubishi F700 Series User Manual

59
Parameter List
Parameter list
4
PARAMETERS

 126
Terminal 4 frequency setting gain
frequency
0 to 400Hz 0.01Hz 50Hz 172
PID control
127
PID control automatic switchover
frequency
0 to 400Hz, 9999 0.01Hz 9999 256
128
PID action selection
10, 11, 20, 21, 40, 41,
50, 51, 60, 61, 70, 71,
80, 81, 90, 91, 100, 101,
110, 111, 120, 121, 140,
141
1 10 256
129
PID proportional band 0.1 to 1000%, 9999 0.1% 100% 256
130
PID integral time 0.1 to 3600s, 9999 0.1s 1s 256
131
PID upper limit 0 to 100%, 9999 0.1% 9999 256
132
PID lower limit 0 to 100%, 9999 0.1% 9999 256
133
PID action set point 0 to 100%, 9999 0.01% 9999 256
134
PID differential time 0.01 to 10.00s, 9999 0.01s 9999 256
Bypass
135
Electronic bypass sequence selection 0, 1 1 0 287
136
MC switchover interlock time 0 to 100s 0.1s 1s 287
137
Start waiting time 0 to 100s 0.1s 0.5s 287
138
Bypass selection at a fault 0, 1 1 0 287
139
Automatic switchover frequency from
inverter to bypass operation
0 to 60Hz, 9999 0.01Hz 9999 287
Backlash measures
140
Backlash acceleration stopping
frequency
0 to 400Hz 0.01Hz 1Hz 98
141
Backlash acceleration stopping time 0 to 360s 0.1s 0.5s 98
142
Backlash deceleration stopping
frequency
0 to 400Hz 0.01Hz 1Hz 98
143
Backlash deceleration stopping time 0 to 360s 0.1s 0.5s 98

144
Speed setting switchover
0, 2, 4, 6, 8, 10, 102,
104, 106, 108, 110
1 4 134
PU
145
PU display language selection 0 to 7 1 1 311

147
Acceleration/deceleration time
switching frequency
0 to 400Hz, 9999 0.01Hz 9999 94
148
Stall prevention level at 0V input 0 to 120% 0.1% 110% 74
Current detection
149
Stall prevention level at 10V input 0 to 120% 0.1% 120% 74
150
Output current detection level 0 to 120% 0.1% 110% 130
151
Output current detection signal delay
time
0 to 10s 0.1s 0s 130
152
Zero current detection level 0 to 150% 0.1% 5% 130
153
Zero current detection time 0 to 10s 0.01s 0.5s 130

154
Voltage reduction selection during
stall prevention operation
0, 1 1 1 74

155
RT signal function validity condition
selection
0, 10 1 0 120

156
Stall prevention operation selection 0 to 31, 100, 101 1 0 74

157
OL signal output timer 0 to 25s, 9999 0.1s 0s 74

158
AM terminal function selection
1 to 3, 5, 6, 8 to 14, 17,
21, 24, 50, 52, 53, 67, 70,
86
1 1 136
Function Parameters
Name Setting Range
Minimum
Setting
Increments
Initial
Value
Refer
to
Page
Customer
Setting

Mitsubishi F700 Series Specifications

General

Humidity	95% RH or less (non-condensing)
Control Method	V/F control
Protection Features	Overcurrent, overvoltage, undervoltage, overheat, short circuit
Communication Options	RS-485
Operating Temperature	-10°C to +50°C
Storage Temperature	-20°C to +65°C
Altitude	Up to 1000m above sea level
Overload Capacity	150% for 60 seconds
Cooling Method	Forced air cooling
Power Range	0.75 to 630 kW (1 to 845 hp)
Output Voltage	3-phase 200 to 240 VAC, 380 to 500 VAC (matching input voltage)