What to do if Mitsubishi Control Unit power supply module capacity is not enough?
Ensure the power capacity is sufficient by calculating the current consumption of connected devices such as the CPU module, I/O module, and intelligent function module.
What to do if Mitsubishi Control Unit power is not supplied?
Verify that the supply voltage of the power supply module is within the rated range.
What to do if Mitsubishi Control Unit offset/gain setting was configured exceeding the maximum number of times?
If the offset/gain setting was configured exceeding the maximum number of times, no more offset/gain setting is reflected on the operation successfully.
What to do if Mitsubishi Control Unit G(P).OGSTOR instruction has been consecutively executed?
Execute the G(P).OGSTOR instruction only once per module. Write the setting value into the flash memory only once for each offset/gain setting.
What to do if Mitsubishi Control Unit G(P).OGSTOR instruction was executed in the offset/gain setting mode?
Do not execute the G(P).OGSTOR instruction in the offset/gain setting mode.
What to do if Mitsubishi Control Unit G(P).OGSTOR instruction has been executed on a different module?
Execute the G(P).OGLOAD and G(P).OGSTOR instructions to the same module.
What to do if Mitsubishi Control Unit values set in CH1 Scaling lower limit value to CH4 Scaling upper limit value are outside the range?
Set a value within the range of -32000 to 32000 in CH1 Scaling lower limit value (Un\G62) to CH4 Scaling upper limit value (Un\G69).
What to do if there is a hardware failure on Mitsubishi Control Unit module?
Power off and on the module. If the error occurs again, a failure might have occurred on the module. Please consult a local Mitsubishi representative.
What to do if Mitsubishi Control Unit settings in CH1 Process alarm lower lower limit value to CH4 Process alarm upper upper limit value are invalid?
Correct the settings in CH1 Process alarm lower lower limit value (Un\G86) to CH4 Process alarm upper upper limit value (Un\G101).
What to do if Mitsubishi Control Unit input range is outside the setting range for Switch 1?
Set a valid value on the intelligent function module switch setting in the parameter setting.
General| Brand | Mitsubishi |
|---|---|
| Model | L Series |
| Category | Engine |
| Language | English |
Precautions related to system design and module protection, including buffer memory usage.
Safety measures for installing the module and system components, covering power supply and module handling.
Safety guidelines for electrical wiring of the module, including grounding and terminal block handling.
Safety measures during initial startup and routine maintenance, covering module handling and static discharge.
Guidelines for safe and environmentally responsible product disposal as industrial waste.
Describes how the A/D converter module is used in practical applications for converting analog signals.
Highlights the key characteristics and capabilities of the A/D converter module, such as high-speed conversion.
Provides fundamental technical specifications for the A/D converter module, referring to safety guidelines.
Details the operational performance metrics like input points, ranges, accuracy, and conversion speed.
Lists all available functions of the A/D converter module with references to their respective sections.
Details the input and output signals used by the A/D converter module, including device numbers and signal names.
Maps buffer memory addresses to their functions, default values, and read/write capabilities.
Illustrates typical system configurations for integrating the A/D converter module with CPU or head modules.
Specifies compatible systems and software versions for the A/D converter module.
Details limitations, such as the non-usability of dedicated instructions, when connecting to a head module.
Guidelines for selecting an appropriate installation environment and location for the module.
Describes the terminal block, including precautions, signal names, and removal/installation procedures.
Provides wiring diagrams for voltage and current inputs to the module's terminal block.
Details the external wiring connections for voltage and current inputs, including shielding and unused channels.
Explains how to add the A/D converter module model name to the project configuration.
Covers setting the input range and operation mode for each channel using the 'Switch Setting' dialog.
Details how to configure various parameters for each channel via the 'Parameter' dialog.
Describes the function for automatically transferring buffer data to specified devices.
Explains how to configure offset and gain settings for user range using GX Works2 or a program.
Explains the processing order and types of digital output values, including scaling and minimum/maximum values.
Details methods for sampling or averaging analog input values, including time, count, and moving averages.
Covers extended input ranges, error detection, and extension functions for analog input signals.
Covers warning output, scaling, shift, digital clipping, and difference conversion functions for output values.
Covers collecting, storing data, and integrating flow amounts, including trigger conditions and cycle settings.
Covers error logging, module error collection, and procedures for clearing errors and alarms.
Allows saving and restoring offset/gain values for user range settings, including methods and procedures.
Describes the LCD display unit for checking system status and error information.
Illustrates the organization and navigation of the display unit's menus for module settings.
Provides a list of screens for changing module settings via the display unit interface.
Outlines the steps for creating programs for A/D conversion, including initial and auxiliary programs.
Shows program examples for standard system configurations, including system setup and programming conditions.
Describes system configuration and programming for head module connections, including initial settings.
Guides on how to check module errors and status through detailed information in the system monitor.
Explains how to check error codes and alarm codes using the Latest Error Code buffer memory.
Describes checking module errors stored by the error collection function in the CPU module.
Provides a comprehensive list of error codes, their causes, and recommended actions.
Lists alarm codes, their causes, and corresponding actions for process and input signal errors.
Offers solutions for common operational issues based on LED status (RUN, ERR, ALM).
Details how to check module LED status and switch settings via the system monitor in GX Works2.
Details the A/D converter module's input and output signals, including flags and requests.
Provides a comprehensive list of buffer memory addresses, their functions, and default values.
Explains the conversion characteristics between analog input and digital output, including offset and gain values.
Lists and describes dedicated instructions for the A/D converter module, such as G(P).OFFGAN.
Describes operating procedures using GX Developer and GX Configurator-AD for module parameter settings.
To Next Page
