VisualMotion 9 Troubleshooting Guide Index 4-1
DOK-VISMOT-VM*-09VRS**-WA02-EN-P
4 Index
!
!01 SERCOS Error Code # xxxx
(xxxx = Error code) ...............3-53
!02 Invalid Parameter Number..3-53
!03 Data is Read Only ..............3-53
!04 Write Protected in this
mode/phase..........................3-53
!05 Greater than maximum value3-
53
!06 Less than minimum value...3-53
!07 Data is Invalid.....................3-53
!08 Drive was not found............3-53
!09 Drive not ready for
communication .....................3-53
!10 Drive is not responding.......3-53
!100 Reset Command Parameter3-
62
!101 Read only From This Port.3-62
!102 Does Not Match Password
Requirements .......................3-62
!103 Bit combination not valid ..3-62
!11 Service channel is not open3-54
!12 Invalid Command Class .....3-54
!13 Checksum Error: xx (xx=
checksum that control calculated)
..............................................3-54
!14 Invalid Command Subclass3-54
!15 Invalid Parameter Set.........3-54
!16 List already in progress ......3-54
!17 Invalid Sequence Number..3-54
!18 List has not started.............3-54
!19 List is finished.....................3-54
!20 Parameter is a List .............3-54
!21 Parameter is not a List .......3-55
!22 Invalid Variable Number .....3-55
!23 Insufficient Program Space 3-55
!24 Maximum number of files
exceeded..............................3-55
!25 Invalid Program Header......3-55
!26 Checksum Error in Program3-
55
!27 Invalid Program Handle......3-55
!28 Function not Implemented..3-55
!29 Program not found on CLC.3-55
!30 Invalid I/O Register or Bit
Number.................................3-56
!31 Invalid Table Index .............3-56
!32 Communication Port Error..3-56
!33 Invalid Data Format ............3-56
!34 Active program can't be deleted
..............................................3-56
!35 Parameter mode is required3-
56
!36 Invalid Event Number .........3-56
!37 Invalid Event Function........3-56
!38 Program file version mismatch
..............................................3-56
!39 Can't activate while program
running..................................3-56
!40 No programs are active ......3-57
!41 System Error: pSOS #XXXX3-
57
!42 Mapper: invalid operator.....3-57
!43 Mapper: too many operations3-
57
!44 Mapper: invalid register ..... 3-57
!45 Mapper: invalid bit or mask 3-57
!46 Mapper: register is read-only3-
57
!47 Invalid Unit Number ........... 3-57
!50 Invalid Download Block...... 3-57
!52 Invalid Axis......................... 3-57
!53 Waiting for service channel3-58
!54 List or String is too short.... 3-58
!55 List or String is too long..... 3-58
!56 PC Communication Handshake
Error..................................... 3-58
!57 I/O Mapper: Max file size on
Control Exceeded ................ 3-58
!58 Cannot store cam: already
active for axis %d................. 3-58
!59 SERCOS handshake/busy
timeout................................. 3-58
!60 Executable program is too large
(ddK).................................... 3-58
!61 System Memory Allocation Error
............................................. 3-58
!62 Cam X data is < 0 or greater
than 360............................... 3-59
!63 X-Column does not start at 0 or
end at 360............................ 3-59
!64 Not supported in user prog file
version 1.1 ........................... 3-59
!72 Program does not include a
PLS...................................... 3-59
!73 Invalid ABS or REL point index
(%d) ..................................... 3-59
!74 Error in command execution3-
59
!75 Comm. port buffer overflow 3-59
!78 Service channel in use ...... 3-59
!79 PID block number does not
exist ..................................... 3-59
!80 Invalid Object Number....... 3-60
!81 Invalid Mapping(s) ............. 3-60
!82 Write protected by password3-
60
!83 Valid ELS Group numbers are 1
through 8.............................. 3-60
!84 ELS Group is not currently
active ................................... 3-60
!85 Data not limited to a specific
ELS Master.......................... 3-60
!86 No ELS Masters are currently
active ................................... 3-60
!87 Valid Virtual Master numbers
are 1 and 2........................... 3-60
!88 No Virtual Master are currently
active ................................... 3-61
!89 Unsupported variable for
mapping............................... 3-61
!90 Invalid variable for mapping3-61
!91 CAM build: float table start
index # ................................. 3-61
!92 CAM build: float table end index
#........................................... 3-61
!93 CAM build: float table size #3-
61
!96 Duplicate Message Sequence
Number (MSN)..................... 3-61
!97 Requested operation prohibited
from network........................ 3-61
!99 Request in Progress.......... 3-61
To Next Page
Loading...
