Cubis MSA User Manual 155
Interfaces
Overview of SBI Commands
Format Command Action/Function Comments
1 ESC P Print to the interface where the prompt originated Corresp. to Menu, with/without stability
1 ESC T “TARE“ key taring and zeroing
1 ESC K Filter “Very stable conditions”
1 ESC L Filter “Stable conditions”
1 ESC M Filter “Unstable conditions”
1 ESC N Filter “Very unstable conditions”
1 ESC O Block keys
1 ESC Q Acoustic signal
1 ESC R Unblock keys
1 ESC S Restart
1 ESC Z Internal calibration/adjustment Depending on menu, 1/2 step increments
1 ESC U Tare
1 ESC V Zero key
1 ESC W Ext. Adjustment with default weight Depending on menu, 1/2 step increments
2 ESC f3_ Zero
2 ESC f4_ Tare (without zeroing)
2 ESC f5_ Left draft shield key (closing and opening as learned or default) Only if available
2 ESC f6_ Right draft shield key(closing and opening as learned or default) Only if available
2 ESC kF1_ Soft key 1, first from right Depends on application
2 ESC kF2_ Soft key 2, second from right Depends on application
2 ESC kF3_ Soft key 3, third from right Depends on application
2 ESC kF4_ Soft key 4, fourth from right Depends on application
2 ESC kF5_ Soft key 5, fifth from right Depends on application
2 ESC kF7_ “Menu” soft key
2 ESC kF9_ “TASK” key
2 ESC kF10_ “USER” key
2 ESC kP_ Print as with “PRINT” key (e. g. to several interfaces)
2 ESC m0_ Ionizer status Only if available
2 ESC m1_ Ionizer on, with preset time Only if available
2 ESC m2_ Ionizer off Only if available
2 ESC s3_ Back, exit, cancel
Models with the Models with the Analytical and
analytical draft shield rotational draft shield rotational draft shield
2 ESC w0_ Draft shield status Draft shield status Only if available
2 ESC w1_ Open left door Open draft shield 100% to the left Only if available
2 ESC w2_ Close all doors Close draft shield Only if available
2 ESC w3_ Open upper door Open draft shield up to position saved Only if available
2 ESC w4_ Open right door Open draft shield door 100% to the right Only if available
2 ESC w5_ Open left and upper doors – Only if available
2 ESC w6_ Open left and right doors – Only if available
2 ESC w7_ Open right and upper door – Only if available
2 ESC w8_ Open all doors – Only if available
2 ESC x0_ Perform internal calibration
2 ESC x1_ Print weigher type
2 ESC x2_ Print serial number
2 ESC x3_ Print balance software version
2 ESC x4_ Print softw. version of display and control unit
2 ESC x5_ Print user/device ID
2 ESC x6_ Print cal./adjust. weight ID
2 ESC x7_ Print batch ID
3 ESC txxx_ Input text
3 ESC txxx_ESC f5_ Enter opening angle xxx in degrees for left key
3 ESC txxx_ESC f6_ Enter opening angle xxx in degrees for right key
3 ESC z5xxx_ Input user/device ID
3 ESC z6xxx_ Input cal./adjust. weight ID
3 ESC z7xxx_ Input batch/lot ID
4 ESC e! {xxx}_ Execute application command, {xxx} = Task ID
4 ESC e? {xxx}_ Query parameter, {xxx} = Parameter ID
4 ESC ea {xxx}_ Save weight value to alibi memory (with optional label), {x…x} = Memory ID
To Next Page
Loading...