Scanivalve MPS4232

To Previous Page

MPS4232



















Main Page

Preface4
Warranty4
Trademarks ® and Copyrights5
Packaging for Shipment5
Important Notice5
Contact Information5
Table of Contents7
Section 1: Specifications13
General Specifications13
Environment Specifications13
Section 2: Introduction16
Overview16
Module Configurations16
Pressure Range16
Valve Actuation16
Pressure Sensors16
Electronics16
Pneumatic Inputs17
Power & Ethernet Connections17
Section 3: Operation19
Unpack & Inventory19
Mounting19
Environmental Considerations19
Warm-Up19
Communications19
Serial Communications19
Ethernet Communications20
Setting up an Ethernet Connection20
Using a Static Ipv4 Address20
PC - Web Server21
Pc - Tcp/Ip Pc - Udp21
PC - Scantel21
PC - Labview21
PC - Hyperterminal21
Scanning22
Scan Rate22
Scan Duration22
Scan Data Format22
Scan Data Units22
Starting a Scan22
Scanning with an External Trigger22
Setting up an External Frame Trigger23
Setting up an External Scan Trigger23
Scan-On-Startup Option23
Scan Data Output Methods23
ASCII TCP Scan Data Transfer23
Binary TCP Scan Data Transfer24
FTP Scan Data Transfer24
UDP Scan Data Transfer24
Binary Data Buffering24
Zero Offset Calibrations (CALZ)25
Ieee1588V2 Precision Time Protocol25
PTP Triggered Scan25
Multiple Unit Operations26
Multiple Unit Scan Command26
Multiple Unit Stop Command27
Multiple Unit Find Command27
Web Server28
Web Server: Main Display29
Web Server: Scan30
Web Server: File Browser32
Section 4: Hardware34
Pneumatic Connections34
Basics of Connecting Input Tubes34
Pressure Measurement (Px) Ports34
Reference (REF) Port34
Removable Pressure Input Headers34
Electrical Connectors35
Power/Serial/Trigger Connection35
Ethernet Connector35
Section 5: Software38
Overview38
MPS Commands38
MPS4200 Buffer Description39
MPS Network Configurations39
Isolated Network39
Integrated with System Network39
Sub-Network with Gateway39
MPS Data Output Definitions39
Host to MPS Command Packet39
MPS to Host ASCII Packet39
Scan Data Formats40
ASCII Scan Data Examples40
Unformatted ASCII40
Formatted ASCII41
Comma Separated Variable ASCII41
Binary Scan Data Formats41
FTP File Names and Formats43
Command Format44
General Control Commands45
Status45
MPS Firmware Version45
MPS Core Versions45
Calibration Version46
Flash Directory Contents46
Delete File46
Load Configuration File46
File Contents47
List47
Save48
Stop48
Reboot49
Format Flash49
Read Current Temperature49
Read Model50
IP Variables52
List IP Settings (LIST IP)52
Set IP Address of the MPS (IPADD)52
Set Subnet of the MPS (SUBNET)52
Set Physical Ethernet Address (MAC)52
Set Gateway (GW)53
Scan Variables54
List Scan Settings (LIST S)54
Set Rate (RATE)54
Set Frames Per Scan (FPS)54
Set Scan Units (UNITS)55
Set Scanning Data Format (FORMAT)56
Set Trigger (TRIG)56
Set Enable FTP (ENFTP)57
Identification Variables58
List Identification Settings (LIST ID)58
Set Serial Number (SN)58
Set Nominal Pressure Range (NPR)58
Set the Multiple Device Multicast Address (MCAST)58
Miscellaneous Variables60
List Miscellaneous Settings (LIST M)60
Set Simulation (SIM)60
Set Echo (ECHO)60
Set Excitation (XITE)60
Set Validation Error Tolerance (ETOL)61
FTP Variables (LIST FTP)62
LIST FTP Settings (LIST FTP)62
Set User Name (USERFTP)62
Set FTP Password (PASSFTP)62
Set FTP IP Address (IPFTP)63
Set FTP File Name (FILEFTP)63
UDP Variables64
List UDP Settings (LIST UDP)64
Set UDP Enable (ENUDP)64
Set the UDP Target Address and Port (IPUDP)64
Calibration and Validation Commands65
Calibration65
Multiple Unit Calibration65
Calibration & Validation65
Multiple Unit Calibration & Validation66
Validation66
Multiple Unit Validation67
Quick-Zero Offset Calibration (CALZ)67
Calibration Variables (LIST C)68
List Calibration Settings (LIST C)68
Set Number of Points in Conversion Table (NUMPTS)68
Set Minimum Calibration and Validation Values (MIN)69
Set Maximum Calibration and Validation Values (MAX)69
Set Oven and Calibrator Delays (DELAY)69
Set the Calibrator IP Address, Port and Calibrator Number (IPCAL)70
Set the Calibration and Validation Average (CALAVG)70
Set Enable CALZ before Validation (VALZO)70
Set Field Calibration Points (FCAL)71
Set Field Validation Points (FVAL)71
Oven Variables (LIST O)72
List Oven Settings (LIST O)72
Set the Oven IP Address, Port and Calibrator Number (Ipoven)72
Set the Oven Start Command (STARTOVEN)72
Set the Oven Stop Command (STOPOVEN)73
Set the Temperature Command (TEMPOVEN)73
Conversion Table Variables74
List Least-Squared Coefficients (LIST T)74
Set Coefficients74
Multicast Commands75
Multiple Unit Find75
Multiple Unit Stop75
Multiple Unit Scan75
Precision Time Protocol Variables (LIST PTP)76
LIST Precision Time Protocol Settings (LIST PTP)76
Set PTP Enable (PTPEN)76
Set PTP Statistical Output (STAT)76
Set Scan Start Time (SST)77
Set Scan Start Date (SSD)77
Set UTC Offset (UTCOFFSET)78
Get PTP Time79
Set PTP Time79
Get UTC Offset79
Section 6: Maintenance82
Firmware Installation (Windows 7, 8, 10)82
Firmware Installation Via Web Server82
Calibration Coefficient Installation (Windows 7, 8, 10)84
Firmware Installation Via Web Server84
Changing the IP Address85
Formatting the Flash Disk86
Calibration & Validation Overview87
Full Calibration & Validation87
Field Calibration & Validation Procedure87
Setup and Configuration87
Performing a Single or Multi-Field Calibration88
Performing a Single or Multi-Field Validation88
Performing a Single or Multi-Field Calibration-Validation89
Performing a Manual Field Calibration or Validation89
Appendix91
Appendix A - Engineering Unit Conversion Constants91
Appendix B - Labview® Client Example92
Appendix C - Data Matrix93
Appendix D - Software Revision Log94

Scanivalve MPS4232 - Page 96

Table of Contents

Related product manuals