MX-M264U SIMULATION 6 – 5
43 1 Used to set the fusing temperature in each mode.
4 Used to set the fusing temperature 2 in each mode.
10 Used to set the postcard feed cycle
20 Used to perform the low-temperature, low-humidity (L/L) environment correction for the fusing temperature
setting of each paper (SIM43-01).
22 Used to perform the low-temperature, low-humidity (L/L) environment correction for the fusing temperature
setting of each paper (SIM43-04).
44 1 Used to set each correction operation function in the image forming (process) section. Image process (Photoconductor/
Developing/Transfer/Cleaning)
9 Used to display the result data of the high density process control operation. Image process (Photoconductor/
Developing/Transfer/Cleaning)
14 Used to display the output level of the temperature and humidity sensor. Process (OPC drum,
development)/Fusing/LSU
43 Used to display the identification information of the developing unit. Developing system
46 2 Used to adjust the copy density in the copy mode.
4 Used to adjust the density in the image send mode.
5 Used to adjust the density in the image send mode.
8 Used to adjust the image send mode color balance RGB.
9 Used to adjust the scan image density.
19 Used to set the operating conditions for the density scanning (exposure) of monochrome auto copy mode
documents.
30 Used to adjust the resolution in the sub scanning direction in the copy mode.
32 Used to adjust the document background density reproducibility in the monochrome auto copy mode.
37 Used to adjust the reproduction capability of monochrome mode color.
39 Used to adjust the sharpness of FAX send images.
40 Used to adjust the FAX send image density. (Collective adjustment of all the modes)
41 Used to adjust the FAX send image density. (Normal)
42 Used to adjust the FAX send image density. (Fine)
43 Used to adjust the FAX send image density. (Super Fine)
44 Used to adjust the FAX send image density. (Ultra fine)
45 Used to adjust the FAX send image density. (600dpi).
47 Used to set the compression rate of copy and scan images (JPEG).
60 Used to adjust the sharpness in the color auto copy mode.
61 Used to adjust the area separation recognition level.
62 Used to set the operating conditions of the ACS, the area separation, the background image process, and
the auto exposure mode.
63 Used to adjust the density in the copy low density section.
48 1 Used to adjust the scan image magnification ratio (in the main scanning direction and the sub scanning
direction).
5 Used to correction the scan image magnification ratio (in the sub scanning direction). Scanner section
49 1 Used to perform the firmware update.
3 Used to update the operation manual in the HDD.
5 Used to perform the watermark update.
50 1 Copy image position, image loss adjustment
2 Used to adjust the copy image position and the image loss. (This simulation is a simplified version of SIM
50-1.)
5 Used to adjust the print lead edge image position. (PRINTER MODE)
6 Used to adjust the copy image position and the image loss. (RSPF mode) RSPF
7 Used to adjust the copy image position and the image loss (RSPF mode).
(This simulation is a simplified version of SIM 50-6.)
RSPF
10 Used to adjust the black print image magnification ratio and the off-center position.
(The adjustment is made separately for each paper feed section.)
12 Used to perform the scan image off-center position adjustment.
(The adjustment is made separately for each scan mode.)
27 Used to perform the image loss adjustment of scanned images in the FAX or image send mode.
28 Used to automatically adjust the image loss, void area, image off-center, and image magnification ratio.
51 2 Used to adjust the contact pressure (deflection amount) on paper by the main unit and the RSPF
registration roller. (This adjustment is performed when there is a considerable variation in the print image
position on the paper or when paper jams frequently occur.)
9 Used to adjust the ON/OFF timing of the separation voltage.
53 6 Used to adjust the detection level of the RSPF document width.
7 Used to adjust the RSPF document size width sensor.
8 Used to adjust the document lead edge reference and the RSPF mode document scan position.
55 1 Used to set the specifications of the engine control operations. (SOFT SW)
2 Used to set the specifications of the scanner control operation. (SOFT SW)
3 Used to set the specifications of the controller operation. (SOFT SW)
10 Used to set the special stamp text. (Taiwan only)
Main Sub Functions Section
To Next Page
Loading...
Need help?
General
