Siemens SIMATIC S5 ET 200U - Page 380

Index-9
ET 200 Distributed I/O Station
EWA 4NEB 812 6087–02b
Repeater, B-5
Repeater adapter, B-6
Request, B-6
Resistance thermometer, connection, 7-10
Response time, B-6
RSAP, 6-33
“RUN” LED, ET 200U(DP Standard), 5-29
“RUN” LED, ET 200U(DP Standard/FMS),
6-35
S
SAC, 6-33
SAP, B-6
SCC, 6-33
Screen, ”CONFIGURING”, 4-6, 5-6
Screen impedance, B-6
Segment, B-6
Sensors/actuators profile, B-6
Service. See FMS service
Service Access Point, B-6
Set station number, IM 318–C, 6-8
Set switch 8, IM 318–C, 6-8
Setting the station number
ET 200U(DP Siemens), 4-18–4-19
ET 200U(DP Standard), 5-21–5-22
Short circuit, B-6
Short circuit proof, B-6
SIGUT screw type connections, 3-12
Simple–Variable, B-6
Simulator module
addressing, 9-9
function, 9-9
installation, 9-9
technical specifications, 9-8
typical application, 9-9
wiring, 9-9
SINEC L2, B-6
SINEC L2–DP, 1-2, 3-1, B-6
Slave initiation, B-6
Slave station, expanding at a later point,
4-15, 5-18
Slave station, already configured, expanding,
4-15, 5-18
Slot, “Input” or “Output” object (slot),
6-14–6-18
Slot numbering, 3-11
Slow Mode, 5-21
Slow mode, ET 200U(DP Siemens), 4-18
Speed of I/O bus
ET 200U(DP Siemens), 4-18–4-19
ET 200U(DP Standard), 5-21–5-22
SPM module, B-6
Standard draft, 1-2, 1-4
Start–up
analog input module, 7-11
ET 200U(DP Siemens), 4-17–4-24
ET 200U(DP Standard), 5-20–5-27
Static object list, 6-13, B-6
Station diagnostics, 4-30, 4-34, 5-33, 5-37
ET 200U(DP Siemens), 4-34
ET 200U(DP Standard), 5-37
ET 200U(DP Standard/FMS), 6-22
“Station diagnostics” header, ET 200U
(DP Standard/FMS), 6-22
Station number, B-7
Station number area
ET 200U(DP Siemens), 4-5
ET 200U(DP Standard), 5-5
Station number label, 2-2
Station status, 4-31, 5-34
ET 200U(DP Siemens), 4-31
ET 200U(DP Standard), 5-34
ET 200U(DP Standard/FMS), 6-20
Status, 6-12
STATUS function
ET 200U(DP Siemens), 4-23
ET 200U(DP Standard), 5-26
Stop/RUN switch, 2-2
Structure of diagnostics
ET 200U(DP Siemens), 4-30
ET 200U(DP Standard), 5-33
Structure of diagnostics data, ET 200U(DP
Standard/FMS), 6-19
Structure of the object list, 6-13
Subindex, B-7
Switch, ”operating mode”, 7-11, 7-12, 7-15
Switch 8, 2-2
SYNC, B-7
SYSTEM START–UP/TEST: MODULE
SELECTION screen
ET 200U(DP Siemens), 4-21
ET 200U(DP Standard), 5-24
SYSTEM START–UP/TEST: STATUS/
CONTROL screen
ET 200U(DP Standard), 5-25
ET 200U(DP–Siemens), 4-22
Index