Name: Topcon IS Series
Brand: Topcon
Rating: 4 (1 reviews)

To Next Page

To Previous Page

4 STANDARD MEASUREMENT MODE

4.2 Angle Measurement

4.2.1 Measuring Horizontal Angle Right and Vertical Angle

Make sure the mode is in angle measurement

Collimate the 1st target (A).

Set horizontal angle of target (A) at 0° 00' 00".

Press the [0SET] key and the [YES] key.

Collimate the 2nd target (B).

The required H/V angle to target B will be

displayed.

Default Chapter3
- Foreword3
1 Nomenclature and Functions14
- Nomenclature14
- Display16
- Backlight, Key Light Adjustment19
- RAM Data Backup24
- Hardware Reset27
- Cover Sensor27
- Touch Panel Calibration28
- Operating Panel Key30
  - Operating Key30
  - Turning off the Touch Panel Function31
- Power off31
- Operation Key(Touch Panel)32
- Star Key Mode34
  - Switching Measurement Distance Modes38
  - Setting by Using Star Key39
- Auto Power off40
- Focus Function42
- Rotating Method44
- Using Together with RC-3 Remote Control System45
- Using Connecting with Personal Computer (PC)46
- Using the USB Port47
2 Preparation for Measurement48
- Power Connection48
- Setting Instrument up for Measurement49
- Power Switch Key on50
- Battery Power Remaining Display51
- Vertical and Horizontal Angle Tilt Correction52
  - Setting Tilt Correction by Operation Key53
  - Correction of a Tilt Sensor Setting Error53
- Compensation of Systematic Error of Instrument54
- How to Enter Numerals and Alphabet Letters55
- Data Memory Card59
- Active Sync60
  - Getting Connected60
- Confirming the Bluetooth® Device Address and Setting the PIN Code60
- Wireless LAN Function ON/OFF61
- Inclination of Prism and Measuring Error61
3 Automatic Tracking / Automatic Collimation63
- Automatic Tracking64
- Automatic Collimation66
- Range of Laser for Auto-Tracking and Auto-Collimating67
- Setting Parameters for Auto-Tracking68
  - Setting Items68
  - How to Set the Parameters70
4 Standard Measurement Mode71
- Screen Displays71
- Angle Measurement74
- Distance Measurement79
- Coordinate Measurement88
- Data Output92
- Data Output by [REC] Key93
- Data Output of IS Series94
5 Program Mode95
- Setting a Direction Angle for Backsight Orientation(BS)96
- Remote Elevation Measurement (REM)98
- Missing Line Measurement (MLM)101
- Repetition Angle Measurement (REP)103
- AP-L1A Communication Emulator105
  - Activate AP-L1A Communication Emulator105
  - Setup for Communication106
- Edge Abstraction Mode107
  - Displayed Messages108
6 Parameters Setting Mode109
- Parameter Setting Options110
- Setting Parameters113
7 Check and Adjustment114
- Checking and Adjusting of Instrument Constant114
  - Checking of the Accuracy of the Non-Prism Mode / Non-Prism Long Mode114
- Checking the Optical Axis115
- Checking/Adjusting each Function123
- How to Set the Instrument Constant Value131
- Compensation Systematic Error of Instrument132
  - Adjustment of Compensation Systematic Error of Instrument132
  - Showing Compensation Systematic Error of Instrument134
- Self Checking Mode135
8 Setting the Prism / Non-Prism Constant Correction Value137
9 Setting Atmospheric Correction139
- Calculation of Atmospheric Correction139
- Setting of Atmospheric Correction Value140
10 Correction for Refraction and Earth Curvature145
- Distance Calculation Formula145
11 Power Source and Charging146
- On-Board Battery BT-65Q146
12 Detach/Attach of Tribrach148
13 Special Accessories149
14 Battery System151
15 Prism System152
16 Precautions153
17 Message/Error Displays154
- Message154
- Error155
18 Specifications157
19 Appendix163
- Dual Axis Compensation163
20 Index165

Brand	Topcon
Model	IS Series
Category	Measuring Instruments
Language	English

Topcon IS Series User Manual

Table of Contents

Questions and Answers:

Topcon IS Series Specifications

Related product manuals