Name: Topcon IS Series
Brand: Topcon
Rating: 4 (1 reviews)

To Next Page

To Previous Page

5 PROGRAM MODE

Press the [YES] key.

Collimate prism.

Press the [Meas Prism] key.

Press the [SET] key.

(To measure the distance again, press the

[RE-TRY] key.)

Collimate target K.

Vertical angle(VA) and Vertical distance(VD)

will be shown.

Default Chapter3
- Foreword3
1 Nomenclature and Functions14
- Nomenclature14
- Display16
- Backlight, Key Light Adjustment19
- RAM Data Backup24
- Hardware Reset27
- Cover Sensor27
- Touch Panel Calibration28
- Operating Panel Key30
  - Operating Key30
  - Turning off the Touch Panel Function31
- Power off31
- Operation Key(Touch Panel)32
- Star Key Mode34
  - Switching Measurement Distance Modes38
  - Setting by Using Star Key39
- Auto Power off40
- Focus Function42
- Rotating Method44
- Using Together with RC-3 Remote Control System45
- Using Connecting with Personal Computer (PC)46
- Using the USB Port47
2 Preparation for Measurement48
- Power Connection48
- Setting Instrument up for Measurement49
- Power Switch Key on50
- Battery Power Remaining Display51
- Vertical and Horizontal Angle Tilt Correction52
  - Setting Tilt Correction by Operation Key53
  - Correction of a Tilt Sensor Setting Error53
- Compensation of Systematic Error of Instrument54
- How to Enter Numerals and Alphabet Letters55
- Data Memory Card59
- Active Sync60
  - Getting Connected60
- Confirming the Bluetooth® Device Address and Setting the PIN Code60
- Wireless LAN Function ON/OFF61
- Inclination of Prism and Measuring Error61
3 Automatic Tracking / Automatic Collimation63
- Automatic Tracking64
- Automatic Collimation66
- Range of Laser for Auto-Tracking and Auto-Collimating67
- Setting Parameters for Auto-Tracking68
  - Setting Items68
  - How to Set the Parameters70
4 Standard Measurement Mode71
- Screen Displays71
- Angle Measurement74
- Distance Measurement79
- Coordinate Measurement88
- Data Output92
- Data Output by [REC] Key93
- Data Output of IS Series94
5 Program Mode95
- Setting a Direction Angle for Backsight Orientation(BS)96
- Remote Elevation Measurement (REM)98
- Missing Line Measurement (MLM)101
- Repetition Angle Measurement (REP)103
- AP-L1A Communication Emulator105
  - Activate AP-L1A Communication Emulator105
  - Setup for Communication106
- Edge Abstraction Mode107
  - Displayed Messages108
6 Parameters Setting Mode109
- Parameter Setting Options110
- Setting Parameters113
7 Check and Adjustment114
- Checking and Adjusting of Instrument Constant114
  - Checking of the Accuracy of the Non-Prism Mode / Non-Prism Long Mode114
- Checking the Optical Axis115
- Checking/Adjusting each Function123
- How to Set the Instrument Constant Value131
- Compensation Systematic Error of Instrument132
  - Adjustment of Compensation Systematic Error of Instrument132
  - Showing Compensation Systematic Error of Instrument134
- Self Checking Mode135
8 Setting the Prism / Non-Prism Constant Correction Value137
9 Setting Atmospheric Correction139
- Calculation of Atmospheric Correction139
- Setting of Atmospheric Correction Value140
10 Correction for Refraction and Earth Curvature145
- Distance Calculation Formula145
11 Power Source and Charging146
- On-Board Battery BT-65Q146
12 Detach/Attach of Tribrach148
13 Special Accessories149
14 Battery System151
15 Prism System152
16 Precautions153
17 Message/Error Displays154
- Message154
- Error155
18 Specifications157
19 Appendix163
- Dual Axis Compensation163
20 Index165

Brand	Topcon
Model	IS Series
Category	Measuring Instruments
Language	English

Topcon IS Series User Manual

Table of Contents

Questions and Answers:

Topcon IS Series Specifications

Related product manuals