Contents
1 Welcome 5
1.1 Target group 5
1.2 Used symbols 5
1.3 Signal words 5
1.4 Copyright 5
2 General safety instructions 6
2.1 Intended use 6
2.2 User skills 6
2.3 Incorrect operation of the machine 6
2.4 Personal injury 6
2.4.1 Electric shock 6
2.4.2 Fire hazard 7
2.4.3 Housing 7
2.4.4 Working chamber 7
2.4.5 Air extraction system 7
2.4.6 Operating noise 7
2.4.7 Maintenance and troubleshooting 7
2.4.8 Spare parts, extra equipment and accessories 7
2.5 Material damage 7
2.5.1 Spindle 7
2.5.2 DENTALCAM & DENTALCNC software 8
2.5.3 Power 8
2.5.4 Air extraction system 8
2.5.5 Working chamber 8
2.5.6 Working chamber door 8
3 Transportation and storage 9
3.1 Handles on the underside of the machine 9
3.2 Transporting the machine in the carton 9
3.3 Preparing transportation or storage 9
3.4 Repackaging 9
3.5 Putting the machine back into operation after storage 9
4 Get to know your machine 10
4.1 Front side of the machine 10
4.2 Rear side of the machine 10
4.3 Connection panel 11
4.4 Start button 11
4.5 Working chamber door 11
4.6 Working chamber 11
4.7 Axes/ A-B axis module 12
4.7.1 Linear axes 12
4.7.2 Rotary axes 12
4.8 Location of the identification plate and serial number 12
4.9 Technical data 13
5 Installation 15
5.1 Checking the scope of delivery 16
5.2 Connecting the machine 17
5.2.1 Machine installation scheme 17
5.2.2 Connecting the CAM computer 17
5.2.3 Installing the air extraction system 18
5.2.4 Establishing the electric connection 20
5.3 Commissioning 21
5.3.1 Starting the machine 21
5.3.2 Setting up a software connection to the machine 21
5.3.3 Removing the spindle lock 23
5.3.4 Warming the spindle 24
6 Operating the machine 25
6.1 Starting the machine 26
6.1.1 Starting the machine 26
6.1.2 Starting the machine with a tool in the collet chuck 26
6.2 Mounting & removing blanks 27
6.2.1 Suitable blanks 27
6.2.2 Overview of blank holders and standard clamping
devices 27
6.2.3 How to mount the different blank types 27
6.3 Mounting discs in the working chamber 28
6.3.1 Removing discs 29
6.4 Mounting blocks and block holders in the working
chamber 30
6.4.1 Mounting blocks to the block holder 30
6.4.2 Mounting the block holder in the working chamber 31
6.4.3 Removing the block holder from the working cham-
ber 31
6.4.4 Removing the blocks from the block holder 32
6.5 Inserting and exchanging tools 33
6.5.1 Automatic or manual tool change 33
6.5.2 Inserting tools into the tool magazine 34
6.5.3 Removing tools from the tool magazine 35
6.5.4 Adding backup tools 35
6.5.5 Using ATB 35
6.6 Starting, interrupting, canceling jobs 37
6.6.1 Starting jobs 37
6.6.2 Interrupt and continue machining 37
6.6.3 Aborting machining 37
6.7 Switching off the machine 39
7 Maintenance 40
7.1 Basic maintenance 40
7.2 Preventive maintenance 40
7.3 Maintenance section 40
Original Operating Instructions: E5
Version: 4/27/2023
EN 3
To Next Page
Loading...
