Xtralis ADPRO FastTrace 2 series - 15 Presidium

110 pages

Save Page as PDF

To Next Page

To Previous Page

Hardware Installation Manual ADPRO

FastTrace™ 2 Series

82 21790_05

15 Presidium

You can associate video outputs from a Presidium with FastTrace 2 analogue inputs. Use coax cables to

connect the video outputs of the Presidium system to the video inputs of the FastTrace 2 video system for

further analysis and recording. It is then possible to transmit alarms from the Presidium to the FastTrace 2

server over the IP network.

See also the XOa Client Software User Manual.

Main Page

Default Chapter1
- Installation Manual1
- Document Conventions3
- Table of Contents5
1 Technical Specifications9
2 Specific Fasttrace Configurations12
- Fasttrace 2 Lite12
- Fasttrace 2X12
- Fasttrace 2E13
- System License13
3 Hard Disks15
- Required Hard Disk Capacity15
- Adding/Replacing a Hard Disk15
- Retrieving Hard Disk Information15
  - Using the Ta,Smart Command15
  - Using the Xoa Client Software16
- Material List (for 1 Hard Disk)17
- Adding Hard Disks with an Intel DH55TC Motherboard17
- Adding Hard Disks with an Intel DH61BE Motherboard20
- Boot Problems after Adding a HDD with the DH61BE Motherboard23
- Adding Hard Disks with a Mitac PH10LU Motherboard24
- RAID 1 Support27
  - About RAID 127
  - Activating RAID 128
4 Fan Speed Selection29
5 Front LED Indicators30
- Overview30
- LED Connections Without Main I/O Card30
- LED Connections with Main I/O Card31
6 Required Motherboard32
- Overview32
- BIOS Settings32
- Replacing the Motherboard33
- Replacing the Motherboard Battery33
7 Extension Boards34
- Overview34
- General Rules35
- Available Configurations35
8 Main and Extension I/O Cards48
- Features48
- Possible Configurations48
- Ordering Information49
- Physical Position49
- Settings on the Main I/O Card50
- Installation50
- Reset Signal Details53
- Adding an Extension I/O Card54
  - Settings on the Extension I/O Card54
  - Installation54
- Adding a Second Set of I/O Cards55
- Connection of Inputs/Outputs55
- Configuring the Internal I/O Cards56
- Input Circuits56
9 Main and Extension I/O Cards Next Generation57
- Features57
- Possible Configurations57
- Ordering Information57
- Material List58
  - Main I/O Card with Mounting Set (#39544000)58
  - Extension I/O Card with Mounting Set (#39544010)60
- Physical Position60
- Settings on the Main I/O Card62
- Installation62
- Reset Signal Details65
- Adding an Extension I/O Card66
  - Settings on the Extension I/O Card66
  - Installation66
- Adding a Second Set of I/O Cards67
- Connection of Inputs/Outputs67
- Configuring the Internal I/O Cards68
- Input Circuits69
10 Required Encoder (A/V) Card70
- Number of Cameras70
- Technical Specifications of Analogue Cameras70
- Replacing a Video Card71
- Adding a Video Card72
- Video Input Termination (75 Ohm/High Impedance)73
11 HIPI Card for IP Cameras74
- Ethernet Settings74
- Adding a HIPI Card76
- Configuring the HIPI Card77
12 Ethernet Card78
- Installation78
- Ethernet Settings78
13 DTC Card79
14 PTZ Cameras80
- Serial PTZ on MIO Card80
- PTZ Via DTC81
- PTZ Via USB Converters81
15 Presidium82
16 Modems83
17 Audio84
- Audio in84
  - Setup84
  - Recommended Microphones84
- Audio out87
  - Setup87
  - Connecting the VM22A Audio Switch88
18 Connecting Pirs89
- Required PIR Firmware89
- Connecting the Pirs89
19 Network Load94
20 Current Consumption95
21 Retrieving the IP Address96
22 Diagnostics97
- Retrieving Traces97
- Retrieving Reports99
23 Fasttrace 2 Web101
24 Maintenance102
- Replacing the Filters102
- Cleaning the Fasttrace 2 Server102
25 Product Labelling103
- Labels103
- Product Number Structure104
  - Fasttrace 2 and Fasttrace 2X Units104
  - Fasttrace 2E Units105
- Declaration of Conformity106
Appendix A: Abbreviations107

Related product manuals

Xtralis ADPRO PRO E

50 pages

Xtralis ADPRO Presidium

122 pages

Xtralis ADPRO FastTrace 2 series - 15 Presidium

Table of Contents

Related product manuals