B.4 Control Mode Dependent Parameter Default Values
534 YASKAWA ELECTRIC SIEP C710636 02B YASKAWA U1000 Technical Manual
Table B.3 A1-02 (Motor 1 Control Mode) Dependent Parameters and Default Values
No. Name Setting Range Resolution
Control Modes (A1-02)
OLV/PM (5) AOLV/PM (6) CLV/PM (7)
b2-01
<14> Default setting value is dependent on the motor code set to parameter E5-01.
<18> Values shown here are for 200 V class drives. Double the value when using a 400 V class drive.
<41> This default value is a calculated as a percentage of the maximum output frequency.
<55> In AOLV/PM and CLV/PM control modes, the setting units and range are expressed as a percent (0.0 to 100.0%) instead of in Hz.
<56> In AOLV/PM and CLV/PM control modes, the setting units and range are expressed as a percent (0.0 to 40.0%) instead of in Hz.
<57> In AOLV/PM and CLV/PM control modes, the setting units and range are expressed as a percent (-100.0 to 100.0%) instead of in Hz.
DC Injection Braking Start Frequency 0.0 to 10.0 0.1 0.5 Hz 1.0%
<41>
0.5%
<41>
b2-04 DC Injection Braking Time at Stop 0.00 to 10.00 0.01 s 0.00 0.00 0.00
b3-01 Speed Search Selection at Start 0 or 1 – 0 0 1
b3-08
Current Control Gain during Speed Search
(Speed Estimation Type)
0.00 to 6.00 – 0.3 0.3 0.3
b3-14
Bi-Directional Speed Search Selection (Speed
Estimation Type, Speed Estimation 2 Type,
Current Detection 3 Type)
0 or 1 – –––
b3-24 Speed Search Method Selection 1 to 4 – 2 2 2
b5-15 PID Sleep Function Start Level 0.0 to 400.0
<55>
0.1 0.0 Hz 0.0% 0.0%
b6-01 Dwell Reference at Start 0.0 to 400.0
<55>
0.1 0.0 Hz 0.0% 0.0%
b6-03 Dwell Reference at Stop 0.0 to 400.0
<55>
0.1 0.0 Hz 0.0% 0.0%
b8-01 Energy Saving Control Selection 0 or 1 – – 1 1
b8-02 Energy Saving Gain 0.0 to 10.0 0.1 – – –
b8-03 Energy Saving Control Filter Time Constant 0.00 to 10.00 0.01 s – – –
C1-11 Accel/Decel Time Switching Frequency 0.0 to 400.0
<55>
0.1 0.0 Hz 0.0% 0.0%
C2-01 S-Curve Time at Accel Start 0.00 to 10.00 0.01 s 1.00 0.20 0.20
C3-01 Slip Compensation Gain 0.0 to 2.5 0.1 – – –
C3-02 Slip Compensation Primary Delay Time 0 to 10000 1 ms – – –
C4-01 Torque Compensation Gain 0.00 to 2.50 0.01 0.00 – –
C4-02 Torque Compensation Primary Delay Time 0 to 10000 1 ms 100 – –
C5-01 ASR Proportional Gain 1 0.00 to 300.00 0.01 – 10.00 20.00
C5-02 ASR Integral Time 1 0.000 to 10.000 0.001 s – 0.500 0.500
C5-03 ASR Proportional Gain 2 0.00 to 300.00 0.01 – 10.00 20.00
C5-04 ASR Integral Time 2 0.000 to 10.000 0.001 s – 0.500 0.500
C5-06 ASR Primary Delay Time Constant 0.000 to 0.500 0.001 s – 0.016 0.004
C5-07 ASR Gain Switching Frequency 0.0 to 400.0
<55>
0.1 – 0.0% 0.0%
C6-02 Carrier Frequency Selection 0 to 4, F – 1 1 1
d3-01 Jump Frequency 1 0.0 to 400.0
<55>
0.1 0.0 Hz 0.0% 0.0%
d3-02 Jump Frequency 2 0.0 to 400.0
<55>
0.1 0.0 Hz 0.0% 0.0%
d3-03 Jump Frequency 3 0.0 to 400.0
<55>
0.1 0.0 Hz 0.0% 0.0%
d3-04 Jump Frequency Width 0.0 to 20.0
<56>
0.1 1.0 Hz 1.0% 1.0%
d5-02 Torque Reference Delay Time 0 to 1000 1 ms – – 0
E1-04 Maximum Output Frequency 40.0 to 400.0 0.1 Hz
<14> <14> <14>
E1-05 Maximum Voltage
<18>
0.0 to 377.1 0.1 V
<14> <14> <14>
E1-06 Base Frequency 0.0 to 400.0 0.1 Hz
<14> <14> <14>
E1-07 Middle Output Frequency 0.0 to 400.0 0.1 Hz – – –
E1-08 Middle Output Frequency Voltage
<18>
0.0 to 377.1 0.1 V – – –
E1-09 Minimum Output Frequency 0.0 to 400.0 0.1 Hz
<14> <14>
0.0
E1-10 Minimum Output Frequency Voltage
<18>
0.0 to 377.1 0.1 V – – –
F1-01 PG 1 Pulses Per Revolution 0 to 60000 1 ppr – – 1024
F1-05 PG 1 Rotation Selection 0 or 1 – – – 1
F1-09 Overspeed Detection Delay Time 0.0 to 2.0 0.1 s – 0.0 0.0
L3-36
Vibration Suppression Gain during Acceleration
(with Current Limit)
0.0 to 100.0 – – – –
L3-41
Vibration Suppression Gain during Deceleration
(with Current Limit)
0.0 to 100.0 – – – –
L1-01 Motor Overload Protection Selection 0 to 6 – 4 4 5
L4-01 Speed Agreement Detection Level 0.0 to 400.0
<55>
0.1 0.0 Hz 0.0% 0.0%
L4-02 Speed Agreement Detection Width 0.0 to 20.0 0.1 2.0 Hz 4.0%
<41>
4.0%
<41>
L4-03 Speed Agreement Detection Level (+/-) -400.0 to 400.0
<57>
0.1 0.0 Hz 0.0% 0.0%
L4-04 Speed Agreement Detection Width (+/-) 0.0 to 20.0 0.1 2.0 Hz 4.0%
<41>
4.0%
<41>
L8-18 Software Current Limit Selection 0 to 1 – 0 0 0
L8-38 Carrier Frequency Reduction Selection 0 to 2 – 0 – 0
L8-40 Carrier Frequency Reduction Off Delay Time 0.00 to 2.00 0.01s 0.00 – 0.00
o1-03 Digital Operator Display Selection 0 to 3 – 0 1 1
o1-04 V/f Pattern Display Unit 0 or 1 – – 1 1
SIEP_C710636_02B_1_0.book 534 ページ ２０１５年１１月２５日 水曜日 午後４時５６分
To Next Page
Loading...
