2gig Technologies Go Control - RF Sensor Chime (0-5) Settings; Wired Sensor Programming Introduction; Wired Sensor Programming Outline

RF Sensor Programming Steps
©2013 2GIG Technologies Inc. All Rights Reserved.
33
Select RF sensor (#) chime (0-5)
DEFAULT: Disabled (0)
EachRFsensorcanbesettosounda“ding‐dong”
chimeand/orsounditsvoicedescriptorwhenthe
sensoristriggered.Thisstepdeterminestheinitial
settingforthesensor.Theendusercanchangethe
chimesettingforsensorsusingChimeSetupinthe
UserToolbox.
•Thedef
ault(0)disablesthechimefo
rthisRF
sensor.
•Ifachimeand/
orvoi
ceisrequiredforthisRF
sensor,chooseoneofthe otherchime
options:
RFSensorChime
(0)disabled (7)ding‐dingwithvoice
(1)voiceonly
(8)ding‐dong#3
(2)ding‐dongwithvoice#1 (9)ding‐dongwithvoice#3
(3)ding‐dong#2
(10)chime#1
(4)ding‐dongwithvoice#2 (11)chime#1withvoice#1
(5)ding‐dong#1
(12)chime#2
(6)ding‐ding (13)chime#2withvoice#2
WIRED SENSOR
PROGRAMMING
Wired Sensor Programming Outline
TheControlPanelcanbeprogrammedwithupto2
wiredsensors.Thewiredsensorsarehardwired
contactloopsconnectedtotheloopinput
terminalsontheControlPanel’ sterminalstrip.To
seewherethe2hardwiredsensorscanbewired
intotheTerminalBlock,seethe"TerminalBlock
WiringDiagram"onpa
ge15.
CAUTION:Wired Sensors CANNOT be used
for a CO or Fire Sensor Loop!
ToprogramthewiredsensorsintotheControl
Panel,dothefollowing:
•Selectthese
nsornu
mber(between1or2)
•Selectthewiredse
nsortype
•Settheequipmentco
de
•Programthelooptype:
•Op
en
•Closed
•End‐of‐li
neresi
stor
•Selecttheotheroptionsforthese
nsor(see
thediagramonthenextpage)
IMPORTANT: Wiredsensors1and2reporttothe
ControlPanelassensors49and50.
Wired Sensor Reporting Codes
WiredSensor#1=ReportsasSensor#49
WiredSensor#2=ReportsasSensor#50
Seethediagramonthenextpageforthesteps
requiredtoprogramwiredsensorsintotheControl
Panel.Theoptionsthatcanbesetforeachwired
sensorare:
•WiredSensorNumber—Sensor#1or2
•WiredSensorTy
pe—
Exit/entry,perimeter,
interior,etc.
•WiredSensorE
quipmen
tType—Certain
sensortypeswillrequiretheinstallertoenter
anequipmenttype(butnotall)
•WiredSensorEquipmen
tCode—4‐digit
equipmentcodethatmatchesinstalledsensor
•WiredSensorE
quipmentAge—Newinstallor
existingsensor
•WiredSensorNor
malSt
ate—normallyopen,
closed,orend‐of‐lineresistorloop
•WiredSensorDialerDel
ay—Delayedor
instantcommunicatorreportsforthesensor
(delaytimeissetbydialerabortwindow)
•WiredSensorVo
ic
eDescriptor—Name
assignedtothesensor
•WiredSensorRepo
rts—Communicator
reportsornocommunicatorreportsforthe
sensor
•WiredSensorChime—
Selectvoice
announcementandchimeoptionsforthe
sensor