2gig Technologies Go Control User Manual

Control Panel Programming Questions
©2013 2GIG Technologies Inc. All Rights Reserved.
45
Q-23 Enter radio modem network
failure time (0-255)
DEFAULT: 30 minutes
NOTE: CellRadioModulemustbeinstalledto
usethisfunction.
Setstheamountoftimere
quiredfortriggeringa
troubleconditionifthesystemdetectsthatthe
optionalcellularradiomodulehaslostitscellular
connection.(Aftercellularservicehasbeen
restoredfor5minutes,thetroublecondition
clears.)
•Thede
fault(30)
setsthefailuredetectiontime
at30minutes.
•Todisableradiomodulefa
iluredetection,
selectdisabled(0).
•Tochoos
eadiff
erentfailuredetectiontime,
select(1‐255)minutes.
Q-24 Select radio modem network
failure causes trouble (0-1)
DEFAULT: Enabled (1)
NOTE: CellRadioModulemustbeinstalledto
usethisfunction.
Selectswhetherthecontr
olpanelwillsoundand
displaytroubleiftheoptionalcellradiomodulehas
lostitscellularconnection.Thetroublesounder
canbesilencedbytheuserattheControlPanel
(cellradiotroubleisloggedregardlessofthis
setting).Whenthecellularradiomodule
connectionisrestored,thetr
oubleindications
aut
omaticallyclear.
•Thedefault(1)allowsra
diomodulefailure
troubleindications.
•Toturnoffrad
iomodulefailuretrouble
indications,selectdisabled(0).
Q-25 Select radio modem network
failure reports (0-1)
DEFAULT: Enabled (1)
NOTE: CellRadioModulemustbeinstalledto
usethisfunction.
Iftheoptionalcellra
diomodulelosesitscellular
connection,theControlPanelcanreportthefault
andrestor evialand‐lineiftelephonereportingis
enabled.
•Thedef
ault(1)allowsra
diomodulefailure/
restorereporting.
•Toturnoffrad
iomodulefailure/restore
reporting,selectdisabled(0).
Q-26 Select auto stay (0-1)
DEFAULT: Enabled (1) (Required SIA CP-
01 Default)
Whenautostayisenabledandthesystemisarmed
intheAwayMode,ifanexit/entrysensorisnot
violatedduringtheExitDelay,thesystemwillarm
intheStayMode.
•Thede
fault(1)enab
lestheautostayfeature.
•Toturnofftheautosta
yfeature,select
disabled(0).
NOTE: Theautostayfeaturedoesnotswitch
thesystemtoStayModeifthesystemis
armedtoAwayModeusingaKeyFob
remoteorremotelyarmedviatelephone,
mobileapp,orcomputer.
Q-27 Select exit delay restart (0-1)
DEFAULT: Enabled (1) (Required SIA CP-
01 Default)
WhenExitDelayrestartisenabled,re‐enteringthe
premisesthroughanexit/entrydoorduringthe
ExitDelaywillrestarttheExitDelay.Therestartof
theExitDelaywillonlyoccuronetime;further
violationsofanexit/entrysensorwillnotextend
theExitDelay.
•Thede
fault(1)enab
lestheExitDelayrestart
feature.
•ToturnofftheExitDe
layrestartfeature,select
disabled(0).
Q-28 Select quick exit (0-1)
DEFAULT: Enabled (1)
Thequickexitfeatureallowstheusertostartthe
ExitDelaywhilethesystemisarmed.Whenthis
featureisenabled,aQuickExitbuttonappearson
theSecurityScreen.PressingQuickExitwhilethe
systemisarmedallowstheusertoleavethrough
anexit/entrydoor.AftertheExitDela
yexpires,th
e
systemwillreturntobeingarmedinthemodeit
wasinbefore(eitherSta yorAwayMode).
•Thede
fault(1)enab
lesthequickexitfeature.
•Toturnoffthequickexi
tfeature,select
disabled(0).

2gig Technologies Go Control Specifications

General

Brand	2gig Technologies
Model	Go Control
Category	Security System
Language	English