2gig Technologies Go Control User Manual

36 ©2013 2GIG Technologies Inc. All Rights Reserved.
Go!Control Wireless Security System | Install Guide
Select wired sensor (#) normal
state
DEFAULT: Not used (0)
Thetwohardwiredloopscanbewiredfornormally
open(N/O)ornormallyclosed(N/C)contacts,or
forend‐of‐line(EOL)resistor.
•Thedef
ault(0)disablesthiswir
edsensor.
•Tousethiswiredsensor
,selectthewaythe
loopiswired:
Wired Sensor Normal State
(0)notuse
d
(1)closed
(2)open
(3)end‐of‐lineres
istor
Select wired sensor (#) dialer delay
(0-1)
DEFAULT: Enabled (1) (Required SIA CP-
01 Default)
Wiredsensorscantriggerthecommunicator
immediatelyorafteradelay.Thedelaytimeisset
bytheabortwindowdialerdelayprogramming
questionQ‐35(thedefaultdelayis30seconds).
•Thedef
ault(1)cau
sesdelayeddialingforthis
wiredsensornumber.
•Forimmedi
atedialingforthiswiredsensor
number,selectdisabled(0).
NOTE: Thisdefaultcanbechangedwithout
aff ectingSIACP‐01compliance.
Construct wired sensor (#) voice
descriptor
DEFAULT: No default
ThevoicedescriptorsarethewordstheControl
Panelwillannounceforthiswiredsensorifthis
wiredsensorisprogrammedforvoice
annunciation.Uptofivewordsareallowed.
1 PressInserttoplaceawordfromthe
vocabularyintothedataentryfield.
2 Usethe←or→arrowstoscrollthroughthe
words,orenterthewor d’s3‐digitindex
number(seetheSystemVocabularyTable.
3 PressInsertagainforthenextword.Uptofive
wordsareallowed.
4 Tomovebetweenwords,presstheFwdand
Backbuttons.
5 Toremoveaword,pressDelete.
Select wired sensor (#) reports
(0-1)
DEFAULT: Enabled (1)
Wiredsensorscanbeprogrammedtotriggera
reporttotheCentralStationornot.
•Thedefault(1)enable
sreportingforthiswired
sensornumber.
•Topreventrep
ortingforthiswiredsensor
number,selectdisabled(0).

Select wired sensor (#) chime (0-5)
DEFAULT: (0) Disabled
Eachwiredsensorcanbesettosounda“ding‐
dong”chimeand/orsoundits
voicedescriptorwhenthesensoristriggered.
•Thedefault(0)disablesth
echimeforthis
wiredsensor.
•Ifachimeand/
orvoi
ceisrequiredforthis
wiredsensor,chooseoneoftheotherchime
options:
Wired Sensor Chime
(0)disabled (7)ding‐dingwithvoice
(1)voiceonly (8)ding‐dong#3
(2)ding‐dongwithvoic
e#1 (9)dingdongwithvoice#3
(3)ding‐dong#2 (10)chime#1
(4)ding‐dongwithvoic
e#2 (11)chime#1withvoice#1
(5)ding‐dong#1 (12)chime#2
(6)ding‐ding (13)chime#2
withvoice#2

2gig Technologies Go Control Specifications

General

Brand	2gig Technologies
Model	Go Control
Category	Security System
Language	English