2gig Technologies Go Control - RF Sensor Programming Steps (Continued); Select RF Sensor (#) Loop Number; Select RF Sensor (#) Dialer Delay; Construct RF Sensor (#) Voice Descriptor

32 ©2013 2GIG Technologies Inc. All Rights Reserved.
Go!Control Wireless Security System | Install Guide
Select RF sensor (#) loop number
(1-3)
DEFAULT: Varies with sensor model
selected
2GIG‐DW10door/windowsensorshavetwoinputs:
aninternalmagneticcontactandanexternal
normallyclosedhardwiredinput.Eitherorboth
sensorinputscanbeused.
TIP: Somesensorsarecap ableofthreeloop
inputs.
Whenusingboththein
te
rnalmagneticcontactand
theexternalinput,themagnetcontactandthe
externalcontactneedtobeassignedadifferent
RFsensornumber.Bothsensornumberswill
sharethesamesensorserialnumber.
•Whenpr
ogra
mmingthesensortousethe
built‐inmagneticcontact,settheloopnumber
to(2).
•Whenprogra
mmingthesensortouseits
hardwiredinput,settheloopnumberas(1).
•Whenpr
ogra
mminga3‐loopsensortousean
additionalinput,settheloopnumberas(3).
•Whenente
ringthesensornumberforthe
sensor’sloop2or3,thepastebuttoncanbe
usedtorecallthelastprogrammedsensor’s
serialnumber. (Thesensornumberwillbe
filledinautomaticallyifLearnisused.)
Select RF sensor (#) dialer delay
(0-1)
DEFAULT: Enabled (1)
(Required SIA CP-01 Default)
RFsensorscantriggerthecommunicator
immediatelyorafteradelay.Thedelaytimeisset
bytheabortwindowdialerdelayprogramming
questionQ‐35(thedefaultdelayis30seconds).
•Thedef
ault(1)cau
sesdelayeddialingforthis
RFsensornumber.
•Forimmedi
atedialingforthisRFsensor
number,selectdisabled(0).
NOTE: ThissettingforCOandsmokedetectors
isautomaticallysettodisabled(0),and
thissub‐questionisskippedforthese
sensortypes.
NOTE: Thisdefaultcanbechangedwithout
aff ectingSIACP‐01compliance.
Construct RF sensor (#) voice
descriptor
DEFAULT: No default
ThevoicedescriptorsarethewordstheControl
Panelwi llannounceforthisRFsensorifthissensor
isprogrammedforvoiceannunciation.Uptofive
wordsareallowed.
1 Pressinserttoplaceawordfromthe
vocabularyintothedataentryfield.
2 Usethe←or→arrowstoscrollthroughthe
words,orentertheword’s3‐digitindex
number(see"SystemV
ocabularyTab
le"on
page27).
3 Pressinsertagainforthenextword.Uptofive
wordsareallowed.
4 Tomovebetweenwords,presstheFwdand
Backbuttons.
5 Toremoveaword,pressDelete.
Select RF sensor (#) reports (0-1)
DEFAULT: Enabled (1)
RFsensorscanbeprogrammedtotriggerareport
totheCentralStationornot.
•Thedefault(1)enab
lesreportingforthisRF
sensornumber.
•Topreventrep
ortingforthisRFsensor
number,selectdisabled(0).
Select RF sensor (#) supervised
(0-1)
DEFAULT: Enabled (1)
Whenasensorissettosupervised,theControl
Panelwillexpectregulartimedsignalsfromthis
sensororelseasensorsupervisorytroublealert
willoccur.
•Thede
fault(1)allowssuperv
isionforthisRF
sensor.
•Toturnoffsuperv
isionforthisRFsensor,
selectdisabled(0).
NOTE: Portablesensorssuchaspanicbuttons
shouldnotbesetassupervisedifthe
sensorwillberemovedfromthepremises
attimes.