2gig Technologies Go Control - RF Key Fob Programming Steps (Continued); Select Fob (#) Used (0-1); Select Fob (#) Equipment Code (0-9999); Enter Key Fob (#) Other Equipment Code (0-9999)

38 ©2013 2GIG Technologies Inc. All Rights Reserved.
RF KEY FOB PROGRAMMING STEPS
Q-3 SELECT FOB # (1-8)
Uptoeightwireless4‐buttonkeyfobscanbeused
witheachControlPanel.Keyfobsreportsas
sensors51‐58.TheoptionsforeachFobare
programmedwithsub‐optionquestions.
•Beginbyen
te
ringtheFobnumberorselectit
usingthe←or→arrows.
•Programthekeyfob
sbyusing↑and↓
arrowstoselectthesub‐options.
NOTE: ToskipRFKeyFobprogramming,press
SkiptojumpfromquestionQ‐3to
questionQ‐4(RFkeypadprogramming).
See"RFKe
ypadProgr
ammingSteps"on
page40.
Select Fob (#) used (0-1)
DEFAULT: Unused (0)
KeyfobscanbeusedwiththeControlPanelornot.
•Thedefault(0)set
sallkeyfobsasunused(0).
•Toenableprogr
ammingforthisKeyFob,select
used(1).
Select Key Fob (#) equipment code
(0-9999)
DEFAULT: (0000) other
TheKeyFobequipmentcodedefinesthesensor’s
manufacturerandtype.
•Thedefaultis(0000)othe
r.
•Select(0866)KEY
2‐3454‐buttonKeyFob
remotefora2GIG‐KEY2KeyFobremote.
•Select(0577)Exi
stingKeyFobremoteforan
existingKeyFobremote.
NOTE: Only2GIG‐KEY1‐345or2GIG‐KEY2‐345
keyfobscanbeusedwiththissystem.
Enter Key Fob (#) other equipment
code (0-9999)
DEFAULT: 0
NOTE: Thisquestionisonlydisplayedif
“(0000)other”isselectedforaKeyFob’s
equipmentcode.
•Theequipmen
tcodeisa4‐digitcodethatis
a
ssignedtothemodelofKeyFobbeingused.
•Entertheequipmentcodenumberfo
rtheKey
Fob.
Enter Fob (#) serial number
(7 digits)
DEFAULT: 0000000
Keyfobserialnumberscanbemanuallyenteredor
learnedfromthefob.
•Formanualentry,en
terthefobnumberthat
wasloggedforthefobbeingprogrammed.Use
theShiftbuttontoaccessalphacharacters.
•Forautom
aticen
try,pressShift,thenpress
Learn.TheControlPanelwillwaitforafob
transmission.Triggerthefobbeing
programmedandtheControlPanelwilllearn
thefob’sserialnumber.
Select Fob (#) equipment age (0-1)
DEFAULT: New (0)
TheControlPanelcanbeusedwithneworexisting
keyfobs.
•Ifthisfobisnewfortheins
tallation,leavethe
defaultofnew(0).
•Ifthisfobisalre
adyinstalled,selectexisting
(1).
Select Fob (#) emergency key (0-4)
DEFAULT: Disabled (0)
Pressingtheandbuttonsonakeyfobatthe
sametimefor5secondscantriggeranemergency
alarm.
•Thede
fault(0)disablesth
eemergency
functionforthisFob.
•Toenabletheemerge
ncyfunctionforthisFob,
select1ofthe4options:
•(0)disabled
•(1
)auxiliaryalar
m
•(2)audiblealarm
•(3
)silentpan
ic
•(4)fire