2gig Technologies Go Control - Walk Test Mode; Signal Strength Indicators; Walk to and Trigger Each Sensor

58 ©2013 2GIG Technologies Inc. All Rights Reserved.
Go!Control Wireless Security System | Install Guide
3 Triggera24‐hourpanicsensor(ifinstalled)or
pressthePanicemergencybutton(ifenabled),
waitabout45secondsforthereportto
complete,thendisarmtheConsole.
4 Triggera24‐houremergencysensor(if
installed)orpresstheEmergencyemergency
button(ifenabled),waitabout45secondsfor
thereporttocomplete,thendisarmthe
Console.
5 Armthesystemthentriggeraburglarysensor,
andwaitforthesystemtogointoalarm,wait
about45secondsforthereporttocomplete
thendisarmtheConsole.
6 CheckwiththeCentralStationthateachzone
(sensortype)wasreported,theninformthe
CentralStationthatthetestingiscomplete.
WALK TEST MODE
WalkTestModeisfortestingallthesensors.It
verifiesthateachsensorisbeingreceivedcorrectly
bytheControlPanel.Thewalktestalsoteststhe
ControlPanel’ sindicatorsandsounder.
NOTE: TheWalkTestModewillautomatically
endafter25minutes.
Signal Strength Indicators
Animportantfeatureisthereceivedsignalstrength
indicatorsdisplayedbytheControlPanelforeach
ofthesensors.EventhoughtheControlPanel’ sRF
receiverishigh‐sensitivity,receptionqualityof
sensorsattheControlPanelcanvaryovertime,
dependingontheamountofbackgroundRFnoise
onthere
ceiver’ sopera
tingfrequency.Thesignal
strengthindicatorsareanimportantaidtothe
installerfordeterminingthebestlocationtomount
thesensorsandControlPanel.
Duringthewalktest,theControlPaneldisplaysthe
signalstrengthoftheRFtransmissionsreceived
fromeachofthesensors.Thishelpstoidentifyan
y
sensor
swithaweaksignalattheControlPanel.
•Re‐mo
untsensorswith
lowsignalstrengthtoa
locationthatproducesstrongerreceptionat
theControlPanel.Thehigherthesensorsignal
strength,thebetter.
Duringthetest
,thesys
temwillbeepevery30
secondstoindicatethatthesystemisinWalkTest
Mode.Duringthelast5minutesofthetest,the
systemwillbeeptwotimesevery30seconds.
NOTE: EnteringtheWalkTestModesendsa
“starttest”reporttotheCentralStation.
ExitingtheWalkTestModesendsa“stop
test”reporttotheCentralStation.
Toperf
ormawalkte
st,dothefollowing:
1 FromtheInstallerToolboxscreen,pressWalk
Test.
2 The icondisplaysontheControlPanel
StatusBarandabeepwillsoundeve
ry30
secondstoindicatethatthesystemisinWalk
TestMode.
3 Eachofthesensorsandtheirstatusareshown
ontheonthesensortestscreen.Usethe↓
and↑arrowstoscrollthroughthesensorlist.
4 Activatethefirstsensorlis tedandviewthe
resultonthedisplay:
•Whenasens
orisrec
eivedbytheControl
Panel,threebeepsoccurandthedisplaylights
agreenbartotheleftofthesensor’sname.
•There
ceivedsignalst
rengthofthesensor
displaysasonetofivegreenbars.Themore
bars,thehigherthesignalstrength.
•Ifthesignallev
elissuf
ficient,acheckmark
displaysforthatsensor.
•Ifthesignallev
elisi
nsufficientorthesignal
testfails,thedisplaylightsaredbar,andan
“x”displaysforthatsensor.
•Forsensorswithmultipleloops,wait15
secondsbetweentriggeringeachloop.
5 Continuetestingwitheachoftheother
sensorslisted.
Afterallthesenso
rshavebeentested,press
OKtotesttheControlPanel’ sindicatorsand
sounder.