2gig Technologies Go Control User Manual

48 ©2013 2GIG Technologies Inc. All Rights Reserved.
Go!Control Wireless Security System | Install Guide
•EnterfourdigitsfortheCentralStation#2
accountnumber.
•TheShiftbutto
naccessesB,C,D,E,andF
characters.
Q-42 Select remote control phone
(0-3)
DEFAULT: Data and voice (3)
Thissettingcontrolsremotetelephoneaccessto
thesystem.Thedataoptionisfortheinstaller.It
allowsaccessforprogrammingandoperatingthe
systemwithcustomPCdownloadersoftware.
Thevoiceoptionisforthesubscriber.Itallowsthe
subscribertocallthesystemfromanoff‐site
phone,togetthesta
tusofthesys
tem,andto
performremotecommands.Thesecommandsare
executedbyenteringtouchtones.Thestatusis
reportedbackviavoiceprompts.AvalidUserCode
isrequiredforremotetelephoneaccess.Theuser
willbeabletoperformthefollowingfunctions:arm
inanymode,di
sarm,bypass,getsy
stemstatus,and
turnonorturnofftheopencollectoroutput.
Ifvoiceaccessisenabled,toconnecttothepanel,
thesubscriberwillneedtocallthetelephone
numberthattheControlPanelisconnectedto,
waitforoneortworings,thenhangup.The
sub
scrib
erneedstocallagain,within10‐45
seconds.TheControlPanelanswersthecall.
Whenthepanelanswersthephone,theuserwill
bepromptedtoentertheircode.Ifavalidcodeis
entered,thesystemwillannouncethecurrent
systemstatus.Ifaninvalidcodeisentered,the
pa
ne
lwillaskforthecodeagain.Aftertwoinvalid
attempts,thepanelwilldisconnect.Aftertwocalls,
withtwoinvalidattemptseach,thepanelwilllock
out.Thelockoutwilllastfor30minutes.
•Thedef
ault(3)enab
lesdataandvoiceaccess.
•Fordataonlyacce
ss,select(1).
•Forvoiceacce
ssonly,select(2).
•Todisableremo
teaccess,select(0).
(0)disabled(noremotecontrolphone)
(1)dataonly
(2)voiceonly
(3)dataand
voice
NOTE: RemotelyarmingthesystemtoAway
ModewillnotstartanExitDelayor
activateAutoStayMode(ifenabled).
Q-43 Enter installer code (4 digits)
DEFAULT: 1561
TheInstallerCodeisthecoderequiredtoenterthe
InstallerToolbox.
•ThedefaultfortheIns
tallerCodeis1561.
•TochangetheInst
allerCode,enteranew4‐
digitcode.
BESURETOWRITEDOWNTHENEWCODE!
NOTE: TheInstallerCodemustbeuniquefrom
anyUserCodes.
Q-44 Select lock installer
programming (0-2)
DEFAULT: Disabled (0)
Theinstallerprogramminglockoutfeatureis
providedtopreventtakeovers.TheControlPanel
canbesettolimitaninstaller’saccessto
programmingquestionsafteraperiodof48hours.
The48hourlockouttimerstartswhentheinstaller
exitssystemconfigurationmode.Threeoptionsare
available:
• unlimitedful
laccess
toprogramming(no
lockout)
•limitedacce
sstoprogr
ammingafter48hours
•noaccesstoprogr
ammingafter48hours
Thedefault(0)selectsunlimitedfullaccessto
programming(nolockout).
Todenyaccesstoprogrammingafter48hours,
selectnoaccesstoprogramming(1).
Toselectlimitedaccesstoprogrammingafter48
hours,select(2).Afterthesystemhasrunfor48
hours,installerwillbeabletoview,butnotchang
e,
theCent
ralStationphonenumber,CentralStation
accountnumber,lockinstallerprogramming,
downloadID,anddefaultlockoutfields.
Afterthe48hourlockouttimerhaslock edoutthe
system,thetimercanberesetthroughthecell
radioorPCdownloaderbyremotelysettingthis
questionQ‐44to(0)or(2
).Settingtheoptio
nto(0)
or(2)willrestartthe48hourlockouttimer.
RemoteControlPhoneMode
TelephoneKey RemoteControlPhoneMode
1 Systemstatusreport
2ArmthesysteminAwayMode
3 ArmthesysteminStayMode
4Disarmthesystem
5 Turnontheauxiliaryoutput
6Turnofftheauxiliaryoutput
7 Stopthesystemstatusreport
8 Disconnect(hangup)
9 Repeatcommandmenu
#Bypassallopensensorsandarmsystem
TelephoneKey RemoteControlPhoneMode

2gig Technologies Go Control Specifications

General

Brand	2gig Technologies
Model	Go Control
Category	Security System
Language	English