2gig Technologies Go Control - Control Panel Programming Questions (Continued); Q-84 Select Services Require Master Code (0-1); Q-85 Select Master User Access to Z-Wave Toolbox (0-1); Q-86 Select Disable Siren After Two-Way Audio (0-1)

Control Panel Programming Questions
©2013 2GIG Technologies Inc. All Rights Reserved.
55
Q-84 Select services require master
code (0-1)
DEFAULT: Disabled (0)
TheServicesbuttoncanbeconfiguredtorequire
theuseoftheMasterUserCodetoaccessServices.
•Thedefault(0)disablesthere
quirementfor
theMasterUserCodetoaccesstheServices
menu.
•Tore
quiretheuseoftheMast
erUserCodeto
accesstheServicesmenu,selectenabled(1).
WhenenabledthentheMast
erUserCodeis
requiredtoaccesstheServicesandtheZ‐wave
deviceconfigurations.Thiskeepsunauthorized
usersfrombeingabletochangeZ‐wavesettings,
suchastemperature,lightsandlocks.
Q-85 Select master user access to
z-wave toolbox (0-1)
DEFAULT: Disabled (0)
TheZ‐WaveToolboxmenucanbesettorequirethe
useoftheMasterUserCodeortheInstallerCode.
Bydefault,theInstallerCodeisrequiredforusers
toaccesstheZ‐WaveToolbox.
•Thedef
ault(0)re
quirestheuseoftheInstaller
CodetoaccesstheZ‐WaveTool boxmenuand
allofitsfeatures,includingtheAdvanced
Toolbox.
•Tore
quiretheuseoftheMast
erUserCodeor
theInstallerCodetoaccesstheZ‐WaveTool
boxmenu,selectenabled(1).
NOTE: Whenenabled(1)theInstallercodewill
stillberequiredtoaccesstheAdvanced
Toolboxmenu.Thispreventsendusers
fromaddingorremovingZ‐Wavedevices.
Q-86 Select disable siren after two-
way audio (0-1)
DEFAULT: Disabled (0)
Thissettingenhancessystemoperationinpersonal
emergencyapplicationsandalsoprovidesthe
dealerwiththeoptionofthesirensoundinguntil
thebellcutoffortotheendofatwo‐way‐voice
session.
•Thedef
ault(0)willca
usethesirentoresume
aftertwo‐wayaudio(ifthebellcutofftimer
hasnotexpired).
• Enable(1) wi
llcau
sethesirentoshutoffafter
atwo‐wayaudiosession.
Q-87 Select keyfob/remote arming
mode on system not ready (0-2)
DEFAULT: Auto bypass with zone
participation on restore (0)
Thissettingcontrolshowthesystemwillreact
whenthereareopensensorsandthesystemis
armedremotely.
•Thede
fault(0)willaut
omaticallybypassall
sensorsthatareopenwhenthesystemis
armedremotely.Ifasensorrestoreswhilethe
systemisarmed,thesensor’sbypasswillbe
removed,andthesensorwillbereadyto
triggeranalarm.
•Toaut
omaticallybypa
ssallsensorsthatare
openwhenthesystemisarmedremotely,and
keepallbypassesinplaceduringthearming
cycle,evenifasensorrestores,selectauto‐
bypass(1).
•Topr
eventarmingrem
otelywhenanysensor
isopen,selectarmonlywhenready(2).
Q-88 Select siren mode (0-1)
DEFAULT: Sound for burglary and fire/
CO (0)
Thissettingselectswhichalarmtypeswillactivate
aZ‐Wavesirenlinkedtothesystem.
•Thedefault(0)willcaus
eaZ‐Wavesirento
soundduringburglaryandfire/COalarms.
•TohaveaZ‐Wav
esirensoundonlyduring
burglaryalarms,selectsoundforburglaryonly
(1).
Q-89 Select allow backlight always
on (demo mode) (0-1)
NOTE: Maycauseghost/imageretention
DEFAULT: Disabled (0)
Whenenabled(1)allowsthecustomertoprogram
the“alwayson”optionforbacklightprogramming.
Duetoasmallpercentageofimage"ghosting"on
thepanel(becausethebacklightnevergoesoff),
thisquestionwasbeencreatedbuthasbeen
defaultedto(0)disabled.