ABB ACQ810 - Page 307

Additional parameter data 307
64.17 AL1 30 to 40% REAL 16 0…100 % -
64.18 AL1 40 to 50% REAL 16 0…100 % -
64.19 AL1 50 to 60% REAL 16 0…100 % -
64.20 AL1 60 to 70% REAL 16 0…100 % -
64.21 AL1 70 to 80% REAL 16 0…100 % -
64.22 AL1 80 to 90% REAL 16 0…100 % -
64.23 AL1 over 90% REAL 16 0…100 % -
64.24 AL2 0 to 10% REAL 16 0…100 % -
64.25 AL2 10 to 20% REAL 16 0…100 % -
64.26 AL2 20 to 30% REAL 16 0…100 % -
64.27 AL2 30 to 40% REAL 16 0…100 % -
64.28 AL2 40 to 50% REAL 16 0…100 % -
64.29 AL2 50 to 60% REAL 16 0…100 % -
64.30 AL2 60 to 70% REAL 16 0…100 % -
64.31 AL2 70 to 80% REAL 16 0…100 % -
64.32 AL2 80 to 90% REAL 16 0…100 % -
64.33 AL2 over 90% REAL 16 0…100 % -
75 Pump logic
75.01 Operation mode enum 16 0…3 - Off
75.02 Nbr of pumps UINT32 16 0…8 - 8
75.03 Follower mode enum 16 0…2 - Master speed
75.04 Follower ref REAL 16 0…32767 rpm 1300 rpm
75.05 Start speed 1 UINT32 32 0…32767 rpm 1300 rpm
75.06 Start speed 2 UINT32 32 0…32767 rpm 1300 rpm
75.07 Start speed 3 UINT32 32 0…32767 rpm 1300 rpm
75.08 Start speed 4 UINT32 32 0…32767 rpm 1300 rpm
75.09 Start speed 5 UINT32 32 0…32767 rpm 1300 rpm
75.10 Start speed 6 UINT32 32 0…32767 rpm 1300 rpm
75.11 Start speed 7 UINT32 32 0…32767 rpm 1300 rpm
75.12 Stop speed 1 UINT32 32 0…32767 rpm 800 rpm
75.13 Stop speed 2 UINT32 32 0…32767 rpm 800 rpm
75.14 Stop speed 3 UINT32 32 0…32767 rpm 800 rpm
75.15 Stop speed 4 UINT32 32 0…32767 rpm 800 rpm
75.16 Stop speed 5 UINT32 32 0…32767 rpm 800 rpm
75.17 Stop speed 6 UINT32 32 0…32767 rpm 800 rpm
75.18 Stop speed 7 UINT32 32 0…32767 rpm 800 rpm
75.19 Start delay UINT32 16 0…12600 s 10 s
75.20 Stop delay UINT32 16 0…12600 s 10 s
75.21 Speed hold on UINT32 16 0…100 s 0 s
75.22 Speed hold off UINT32 16 0…100 s 0 s
No. Name Type
Data
len.
Range Unit
Default (Factory
def macro)