Akai S3200XL

To Next Page

To Previous Page

EDIT SAMPLE

S3200XL Operator’s Manual - Version 1.00 Page 153

REVERSING SAMPLES

In the PARAMETERS page, when the soft key (F8) is pressed, the sample will be

reversed. Pressing it again will reverse the sample back to its original form. Note that any loop

points you have set will stay in the same absolute positions, and will not be reversed with the

sample.

Main Page

Default Chapter7
- Fcc Warning7
- Table of Contents9
Introduction15
- Features16
- About this Manual19
- Front Panel20
- Taking Care of Your Disks22
- Rear Panel24
- Setting up the S3200Xl27
- Connections27
- Loading the Demo Floppy Disks28
- Mounting the S3200Xl29
- Getting Around the S3200Xl30
- Record Level, Main Volume, Headphone Output34
- How the S3200Xl Works35
- S3200Xl Flowchart36
S I N G L E M O D39
- Selecting Programs39
- Viewing Programs40
- Setting Program Levels, Pan, Fx Sends40
- Setting Programs' MIDI Parameters41
- Single Mode42
- Setting Program Loudness and Velocity43
- Loading from Floppy Disk44
- Loading from Hard Disk45
- Deleting Programs46
- Renumbering Programs48
- Using the S3200Xl in 'Old Akai' Mode49
Multi Mode - Combining Several Programs53
- Assigning Programs to Parts54
- Setting a Part's MIDI Channel54
- Mixing the Parts54
- Sending Parts to the Internal Effects54
- Assigning Parts to the Individual Outputs55
- Tuning and Transposing Parts55
- Setting a Part's Low and High Keyranges55
- Setting a Part's Priority56
- Initialising a Part56
- Setting up a Multi57
- Modifying the Multi58
- Naming a Multi59
- Saving a Multi59
- Loading a Multi59
- Renumbering Programs60
- Using Multi Mode for Layering Programs63
- Using Multi Mode to Set Keyboard Splits64
Program Editing66
- What Is a Keygroup67
- Keygroup Zones68
- Overlapping and Crossfading Keygroups69
- Assignable Program Modulation70
- Edit Single74
- Naming Programs - Copying and Renaming75
- Deleting Programs76
- MIDI Page80
- Output Levels Page82
- Pan Page85
- The Tune Page87
- Modulation Pages88
  - Pitch Bend88
  - Lfo190
  - Setting Lfo1 Modulation Depth93
  - Lfo294
  - Setting up the Soft Pedal97
  - Portamento98
- Keygroup Parameters - Creating Keygroups101
  - Mapping out Your Keygroups - Setting Keyspan104
- Assigning Samples to Keygroups and Zones - Smp1106
  - Smp2109
  - Smp3111
- The Filters112
- Env1 - Shaping Amplitude115
- Env2 - Shaping the Filter117
  - Using the Filter and Envelope Generators118
- The Second Filters119
  - CREATING 24Db/8Ve 4-POLE LOWPASS FILTER123
  - The Tone Page125
- Env3127
- Keygroup Pitch/Amplitude Modulation128
Edit Multi130
- Screen Differences in Edit Multi130
Sample Mode132
- What Is Sampling132
- Record Mode134
- The Main Record Page137
- Naming Samples for Recording137
- Adjusting the Recording and Threshold Levels139
- Recording on the S3200Xl139
- Digital Recording140
Edit Sample142
- Naming Samples - Copying and Renaming144
- Deleting Samples145
- Trimming Samples146
- Looping150
- Loop Auto Find and Crossfade Looping151
  - Making a Good Loop153
- Level Normalisation155
- Dsp Functions - Timestretch, Re-Sampling and Eq156
- Further Editing Functions165
Effects Mode176
- Organisation of Effects Files178
- Assigning Effects to Single Programs179
- Assigning Effects to Multi Parts181
- Assigning Effects to Individual Keygroups183
- Processing External Sound Sources through the Effects184
- Routing External Sounds through the Effects185
- Selecting the Effects Output185
- Chaining Effects186
- Muting Effects188
Effects Edit189
- Distortion/Ring Modulation190
- Modulation Effects193
- Delay and Echo Effects201
- Reverb Effects207
  - Reverse Reverb210
  - Gated Reverb211
- Effects Output Section213
- Effects Direction214
- Soloing the Current Effect216
- Copying Effects217
- Copying Effects between Different Effects Files217
Save Mode219
- Selecting Floppy or Hard Disk219
- Selecting the Hard Disk Partition219
- Selecting the Hard Disk Volume219
- Selecting the Type of Save219
- Saving to Floppy Disk221
- Saving to Hard Disk222
- Renaming Files224
- Deleting Items from Disk225
- Hard Disk Control226
- Formatting a Floppy Disk227
- Formatting a Hard Disk229
- Notes on Using Existing S1000/S1100 Sound Library230
Load Mode231
- Selecting Floppy or Hard Disk231
- Selecting the Hard Disk Partition231
- Selecting the Hard Disk Volume232
- Selecting the Type of Load232
- Loading from Floppy Disk233
- Loading from Hard Disk234
- Loading S900/S950 Samples and Programs236
- Loading S1000/S1100 Data236
- Auto Loading from Disk236
- Searching for Files - Using the Find Function237
- Using the Tag Directory System239
  - Naming Tags240
  - Notes on Using the Tagging System240
- Hard Disk Control242
- Importing Sounds from Other Manufacturer's CD-Roms243
Global Mode245
- Tuning the S3200Xl245
- Setting the Master Output Level245
- MIDI Functions246
- Me35T Drum Settings252
- Dat Back-Up and Restore254
  - Performing a Dat Back up255
  - Performing a Dat Restore255
- Standard MIDI File - MIDI Song File Play256
  - Loading Standard MIDI Files257
  - Using the Smf Function258
- Hard Disk Recording259
- Smpte Page - Using Cue Lists294
Appendix 1303
Appendix 1303
- Connecting an External Hard Disk Drive303
- Connecting Two Samplers to One Hard Disk Drive303
- Notes on Using Hard Disk Drives304
Appendix 2306
Appendix 2 Data Compatibility Issues306
- Sound Data306
- Effects Files307
- Multis307
- Me-35T Drum Settings307
- Songs and Qlists307
Appendix 3308
Appendix 3 Installing Extra Memory308
- Installing Memory Expansion308
Appendix 5311
Appendix 4311
Appendix 4 MIDI Controller List311
- Specifications317
Specifications318
S3200Xl MIDI Implementation Chart318

Table of Contents

Related product manuals