Amada WELD CHECKER MM-400A - Page 3

MM-400A
Contents
2
e. COMPARATOR Screen ..................................................................................................................... 8-18
f. ENVELOPE Screen ........................................................................................................................... 8-21
g. HISTORY Screen .............................................................................................................................. 8-37
h. PRINT Screen .................................................................................................................................... 8-41
i. USB Screen ....................................................................................................................................... 8-45
j. ALL CYCLE Screen ........................................................................................................................... 8-56
k. FORCE TIMING Screen .................................................................................................................... 8-61
l. BASIC SETUP Screen ....................................................................................................................... 8-64
m. EXTEND SETUP Screen ................................................................................................................... 8-84
n. SYSTEM SETUP Screen ................................................................................................................. 8-103
o. EXT INPUT/OUTPUT Screen .......................................................................................................... 8-113
p. COMMUNICATION Screen ............................................................................................................. 8-123
q. INTERNAL MEMORY Screen .......................................................................................................... 8-130
r. SEAM WAVEFORM Screen ............................................................................................................ 8-135
s. SEAM SETUP Screen ..................................................................................................................... 8-137
9. Measurement ................................................................................................................... 9-1
(1) Measuring Current (Current Flow Time)/Voltage ......................................................... 9-1
(2) Measuring Displacement (Force/displacement-equipped specification function) ........ 9-7
(3) Measuring Force (Force/displacement-equipped specification function) ................... 9-12
(4) Measuring Current/Voltage after FORCE INITIAL ..................................................... 9-16
(5) Continuously Measuring Displacement, Force and External Input
(Force/displacement-equipped specification function) .................................................... 9-22
10. Interface ......................................................................................................................... 10-1
(1) Connection Diagram of the External I/O Signals ....................................................... 10-1
a. Input Connector ................................................................................................................................. 10-1
b. Output Connector (D-Sub, 37-pin, female) ........................................................................................ 10-2
(2) Description of the External I/O Signals ...................................................................... 10-3
a. Input Connector (D-Sub, 25-pin, female) ........................................................................................... 10-3
b. Output Connector (D-Sub, 37-pin, female) ........................................................................................ 10-5
(3) Connection of Input Signals ....................................................................................... 10-7
a. Connection with device having a contact input (when using internal power supply) .......................... 10-7
b. Connection with device featuring NPN open collector output (when using internal power supply) .... 10-7
c. Connection with device featuring PNP current output (when using external power supply) ............... 10-8
d. Connection with device featuring NPN open collector output (when using external power supply) ... 10-8
(4) Interface of Other Connectors ................................................................................... 10-9
a. Displacement sensor connector ......................................................................................................... 10-9
b. Displacement connector (Mitutoyo, Ono Sokki, KEYENCE, HEIDENHAIN, 10-pin) .......................... 10-9
c. Force sensor connector ..................................................................................................................... 10-9
d. Multiconnector ................................................................................................................................. 10-10
e. Communication connector (RS-232C/485) ...................................................................................... 10-10
11. Timing Chart .................................................................................................................. 11-1
(1) Schedule Number Selection ...................................................................................... 11-1
(2) NO CURR Operation ................................................................................................. 11-2
(3) Internal Processing Time ........................................................................................... 11-4
(4) Judgment Output ....................................................................................................... 11-5
(5) Single-Directional Communication, Single-Directional Communication Time of
Measured Value .............................................................................................................. 11-6
(6) Bi-Directional Communication after Measurement .................................................... 11-7
12. Data Communication .................................................................................................... 12-1
(1) Data Transfer ............................................................................................................. 12-1
(2) Configuration ............................................................................................................. 12-2
a. RS-232C ............................................................................................................................................ 12-2
b. RS-485 ............................................................................................................................................... 12-2
c. Ethernet ............................................................................................................................................. 12-3
(3) Communication Protocol (Single-Directional Communication) .................................. 12-7
(4) Communication Protocol (Bi-Directional Communication) ....................................... 12-22
(5) Code Table of Communication and USB Data ........................................................ 12-67