Amada WELD CHECKER MM-400A - 8. Operation Screens; (1) Operation Screen Organization

328 pages

Save Page as PDF

To Next Page

To Previous Page

MM-400A

7. Basic Operation

7-7

(4) Shutdown

1) Set the main power switch on the rear panel to the OFF position (O side).

Main Page

Table of Contents2
Special Precautions5
Safety Precautions5
Precautions for Handling8
Model-Specific Function8
Use of Printer8
On Disposal8
Warning Labels9
Features10
Packaging12
Accessories12
Options12
Name and Functions of each Section16
Front16
Rear17
Operation Flow19
Installation and Connections20
Installing the MM-400A20
Preparations for Measurement - Connection between the MM-400A and Measurement Devices21
Connecting the Toroidal Coil and the Voltage Detection Cable21
Connecting the Displacement Sensor (Force/Displacement-Equipped Specification)24
Connecting the Force Sensor (Force/Displacement-Equipped Specification)27
When Using an External ±10 V Voltage Input (Force/Displacement-Equipped Specification)30
When Using an External 4 to 20 Ma Current Input (Force/Displacement- Equipped Specification)31
When Using a Shunt Resistor (Force/Displacement- Equipped Specification)32
Basic Operation34
Startup34
Changing the Display Language35
Basic Usage of the MM-400A35
Shutdown40
Operation Screens41
Operation Screen Organization41
Description of the Operation Screens44
MENU Screen44
MEASUREMENT Screen46
VIEW Screen49
WAVEFORM Screen54
COMPARATOR Screen58
ENVELOPE Screen61
HISTORY Screen77
PRINT Screen81
USB Screen85
ALL CYCLE Screen96
FORCE TIMING Screen101
BASIC SETUP Screen104
EXTEND SETUP Screen124
SYSTEM SETUP Screen143
EXT INPUT/OUTPUT Screen153
COMMUNICATION Screen163
INTERNAL MEMORY Screen170
SEAM WAVEFORM Screen175
SEAM SETUP Screen177
Measurement182
Measuring Current (Current Flow Time)/Voltage182
Measuring Displacement (Force/Displacement-Equipped Specification Function)188
Measuring Force (Force/Displacement-Equipped Specification Function)193
Measuring Current/Voltage after FORCE INITIAL197
Continuously Measuring Displacement, Force and External Input (Force/Displacement-Equipped Specification Function)203
Interface205
Connection Diagram of the External I/O Signals205
Input Connector205
Output Connector (D-Sub, 37-Pin, Female)206
Description of the External I/O Signals207
Input Connector (D-Sub, 25-Pin, Female)207
Output Connector (D-Sub, 37-Pin, Female)209
Connection of Input Signals211
Connection with Device Having a Contact Input (When Using Internal Power Supply)211
Connection with Device Featuring PNP Current Output (When Using External Power Supply)212
Connection with Device Featuring NPN Open Collector Output (When Using External Power Supply)212
Interface of Other Connectors213
Displacement Sensor Connector213
Displacement Connector (Mitutoyo, Ono Sokki, KEYENCE, HEIDENHAIN, 10-Pin)213
Force Sensor Connector213
Multiconnector214
Communication Connector (RS-232C/485)214
Timing Chart215
Schedule Number Selection215
CURR Operation216
Internal Processing Time218
Judgment Output219
Single-Directional Communication, Single-Directional Communication Time of Measured Value220
Bi-Directional Communication after Measurement221
Data Communication222
Data Transfer222
Configuration223
Rs-232C223
Ethernet224
Communication Protocol (Single-Directional Communication)228
Communication Protocol (Bi-Directional Communication)243
Code Table of Communication and USB Data288
Error List and Maintenance296
Troubleshooting296
Replacing the Battery302
Necessary Items302
Maintenance Parts302
Replacement Procedure302
Replacing the Fuse305
Maintenance Parts305
Replacement Procedure305
Specifications306
Measurement Specification306
Specification of the MM-400A311
Calibration312
Outline Drawing313
Displacement Sensor314
LG200-110 Type, Mitutoyo314
Type, Mitutoyo (Discontinued)315
LG100-125 Type, Mitutoyo316
GT2-P12 Type, KEYENCE317
ST1278 Type, HEIDENHAIN318
Schedule Data Table319
Index327

Amada WELD CHECKER MM-400A - 8. Operation Screens; (1) Operation Screen Organization

Table of Contents

Related product manuals