Barco HDX series - Page 351

351 pages

To Previous Page

To Previous Page

Loading...

Revision Sheet

To:

Barco nv Media & Entertainment Division/Documentation

Noordlaan 5, B-8520 Kuurne

Phone: +32 56.36.82.11, Fax: +32 56.36.88.24

Support: www.Barco.com/esupport, Web: www.barco.com

From:

Date:

Please correct the following points in this documentation (R5905032/00):

page wrong

correct

R5905032 HDX SERIES 01/06/2011

Table of Contents

Default Chapter5
- Table of Contents5
1 Safety9
- General Considerations10
- Important Safety Instructions11
- Important Warnings Concerning HDX Flight Cases14
2 General15
- Installation Requirements16
- Unpacking the Projector17
- Initial Inspection19
- HDX Flight Case20
- Rear Projection21
- Projector Conﬁgurations21
- Positioning the Projector23
- Projector Air Inlets and Outlets25
- Free Download of Projector Toolset26
- Installation Process Overview27
3 Physical Installation29
- Remote Control Unit (RCU)30
- Lenses36
- Connecting the Projector with the Power Net48
- Alignment of a Table Mounted Projector49
- Mounting the Bottom Carry Handler50
- Mounting the Top Carry Handler52
- Suspension of the Projector with Rigging Clamps53
- Alignment of a Ceiling Mounted Projector56
4 Input & Communication57
- Introduction58
- Input Source Connections59
- Communication Connections61
- Utility-Accessory Outlet64
5 Getting Started65
- How Controlling the Projector66
- RCU & Local Keypad66
- Remote Control Functions66
- Terminology Overview67
- Power on Projector69
- Software Overview70
- Switching to Standby72
- Power off Projector73
- Status Leds74
- Using the RCU75
- Projector Address76
  - Displaying and Programming Addresses into the RCU77
  - Controlling the Projector78
- Source Selection79
6 Quick Set up Adjustment81
- Text Boxes on or off82
- Quick Lens Adjustment Via LENS Key83
- Direct Lens Adjustment (RCU)85
- Quick Picture in Picture86
- Quick Language Selection87
7 Start up of the Adjustment Mode89
- About the Adjustment Mode90
- About the Use of the Remote Control and the Local Keypad91
- Start up the Adjustment Mode92
- Navigation and Adjustments93
- Menu Memory94
- Shortcut Keys to the Menus95
- Test Patterns in Adjustment Mode96
8 Input97
- Input Menu Overview98
- Slot Module Type99
- Input Locking106
- Native Resolution108
- No Signal110
9 Image117
- Image Menu Overview118
- Start up the Image Adjustments119
- Image Settings120
- Aspect Ratio135
- Timings137
  - Source Timings138
  - Advanced Timings, Clamp Delay - Clamp Width139
- Image File Services141
- Save Custom Settings153
10 Layout155
- Layout Menu Overview156
- Introduction157
- Main Window158
- Pip Window164
- Layout File Services171
- Zoom - Focus - Shift Windows177
11 Lamp179
- Lamp Menu Overview180
- Lamp Power Mode181
- Lamp Power182
- Auto Dimming When on Pause183
- CLO Mode (Constant Light Output Mode)184
- CLO Targets186
- How to Display187
- Lamp Identiﬁcation187
- Z-Axis Adjustment188
12 Alignment189
- Alignment Menu Overview190
- Orientation191
- Lens Adjustment, Zoom - Focus192
- Lens Adjustment, Shift193
- Lens Adjustment, MID Position194
- Home Lens at Startup195
- Calibrate Lens196
- Warping197
- Blanking Adjustment208
- Contrast-Intensity210
- Gamma211
- Internal Patterns212
- Color Space213
- Scenergix215
13 Projector Control229
- Projector Control Menu Overview230
- Individual Projector Address231
- Projector Common Address232
- Serial Communication233
  - Baud Rate Setup234
  - Interface Standard235
- Network236
- IR Control Switching252
- DMX253
- Buttons259
  - Standby Button260
  - Shortcut Keys261
- Menu Position262
- Local LCD263
- Language Selection264
14 Service265
- Service Menu Overview266
- Identiﬁcation267
- What Can be Seen267
- Diagnosis269
- Internal Service Patterns281
- Convergence284
- Factory Defaults286
- USB Memory287
- Reset Formatter289
- Reﬁll Mode290
- Save Custom Settings291
- Special HD Camera Mode292
- Auto Dimming When Over-Temperature293
- Time and Date294
15 Maintenance295
- Cleaning the Lens296
- Cleaning the Exterior of the Projector297
16 Servicing299
- Inserting an Input Module300
- Removal of the Lamp House301
- Installation of the Lamp House303
- Removal of the304
- Mounting the306
- Removal of the Lamp Cover308
- Mounting the Lamp Cover309
- Replacement of the High Density Dust Filter310
- Remove and Clear Metal Front Filter311
Dimensions313
- Dimensions of a HDX Projector314
Speciﬁcations315
- Speciﬁcations of the HDX W14317
- Speciﬁcations of the HDX W12319
Standard Source Files321
- C.1 Table Overview323
DMX Chart327
- DMX Chart, Basic328
- DMX Chart, Full329
- DMX Chart, Extended330
Stacking HDX Projectors331
- Mount Stacking Points332
- Stacking HDX Projectors333
- Aligning Stacked HDX Projectors336
Environmental Information339
- Disposal Information341
- Rohs Compliance342
- F.2 Rohs Compliance342
Index345

Related product manuals

Preview: Barco HDX

Preview: Barco FLM HD20

Preview: Barco HDF W series

Barco HDF W series

Preview: Barco SIM 7Q HB

Barco SIM 7Q HB

Preview: Barco F50

Preview: Barco Freya

Preview: Barco Bragi

Preview: Barco SIM 7D

Preview: Barco DP2K-20C