Name: Barco HDX series
Brand: Barco
Rating: 5 (1 reviews)

To Next Page

To Previous Page

7. Start up of the adjustment mode

7.3 Start up the adjustment mode

Start up tools

To start up the adjustment mode, use the remote control or the local keypad.

How to start up?

1. Press Menu on the remote control (RCU) or on the local keypad to start up the Adjustment mode.

The main menu of the adjustment mode opens.

Image 7-1

Main menu

88 R5905032 HDX SERIES 01/06/2011

Default Chapter5
- Table of Contents5
1 Safety9
- General Considerations10
- Important Safety Instructions11
- Important Warnings Concerning HDX Flight Cases14
2 General15
- Installation Requirements16
- Unpacking the Projector17
- Initial Inspection19
- HDX Flight Case20
- Rear Projection21
- Projector Conﬁgurations21
- Positioning the Projector23
- Projector Air Inlets and Outlets25
- Free Download of Projector Toolset26
- Installation Process Overview27
3 Physical Installation29
- Remote Control Unit (RCU)30
- Lenses36
- Connecting the Projector with the Power Net48
- Alignment of a Table Mounted Projector49
- Mounting the Bottom Carry Handler50
- Mounting the Top Carry Handler52
- Suspension of the Projector with Rigging Clamps53
- Alignment of a Ceiling Mounted Projector56
4 Input & Communication57
- Introduction58
- Input Source Connections59
- Communication Connections61
- Utility-Accessory Outlet64
5 Getting Started65
- How Controlling the Projector66
- RCU & Local Keypad66
- Remote Control Functions66
- Terminology Overview67
- Power on Projector69
- Software Overview70
- Switching to Standby72
- Power off Projector73
- Status Leds74
- Using the RCU75
- Projector Address76
  - Displaying and Programming Addresses into the RCU77
  - Controlling the Projector78
- Source Selection79
6 Quick Set up Adjustment81
- Text Boxes on or off82
- Quick Lens Adjustment Via LENS Key83
- Direct Lens Adjustment (RCU)85
- Quick Picture in Picture86
- Quick Language Selection87
7 Start up of the Adjustment Mode89
- About the Adjustment Mode90
- About the Use of the Remote Control and the Local Keypad91
- Start up the Adjustment Mode92
- Navigation and Adjustments93
- Menu Memory94
- Shortcut Keys to the Menus95
- Test Patterns in Adjustment Mode96
8 Input97
- Input Menu Overview98
- Slot Module Type99
- Input Locking106
- Native Resolution108
- No Signal110
9 Image117
- Image Menu Overview118
- Start up the Image Adjustments119
- Image Settings120
- Aspect Ratio135
- Timings137
  - Source Timings138
  - Advanced Timings, Clamp Delay - Clamp Width139
- Image File Services141
- Save Custom Settings153
10 Layout155
- Layout Menu Overview156
- Introduction157
- Main Window158
- Pip Window164
- Layout File Services171
- Zoom - Focus - Shift Windows177
11 Lamp179
- Lamp Menu Overview180
- Lamp Power Mode181
- Lamp Power182
- Auto Dimming When on Pause183
- CLO Mode (Constant Light Output Mode)184
- CLO Targets186
- How to Display187
- Lamp Identiﬁcation187
- Z-Axis Adjustment188
12 Alignment189
- Alignment Menu Overview190
- Orientation191
- Lens Adjustment, Zoom - Focus192
- Lens Adjustment, Shift193
- Lens Adjustment, MID Position194
- Home Lens at Startup195
- Calibrate Lens196
- Warping197
- Blanking Adjustment208
- Contrast-Intensity210
- Gamma211
- Internal Patterns212
- Color Space213
- Scenergix215
13 Projector Control229
- Projector Control Menu Overview230
- Individual Projector Address231
- Projector Common Address232
- Serial Communication233
  - Baud Rate Setup234
  - Interface Standard235
- Network236
- IR Control Switching252
- DMX253
- Buttons259
  - Standby Button260
  - Shortcut Keys261
- Menu Position262
- Local LCD263
- Language Selection264
14 Service265
- Service Menu Overview266
- Identiﬁcation267
- What Can be Seen267
- Diagnosis269
- Internal Service Patterns281
- Convergence284
- Factory Defaults286
- USB Memory287
- Reset Formatter289
- Reﬁll Mode290
- Save Custom Settings291
- Special HD Camera Mode292
- Auto Dimming When Over-Temperature293
- Time and Date294
15 Maintenance295
- Cleaning the Lens296
- Cleaning the Exterior of the Projector297
16 Servicing299
- Inserting an Input Module300
- Removal of the Lamp House301
- Installation of the Lamp House303
- Removal of the304
- Mounting the306
- Removal of the Lamp Cover308
- Mounting the Lamp Cover309
- Replacement of the High Density Dust Filter310
- Remove and Clear Metal Front Filter311
Dimensions313
- Dimensions of a HDX Projector314
Speciﬁcations315
- Speciﬁcations of the HDX W14317
- Speciﬁcations of the HDX W12319
Standard Source Files321
- C.1 Table Overview323
DMX Chart327
- DMX Chart, Basic328
- DMX Chart, Full329
- DMX Chart, Extended330
Stacking HDX Projectors331
- Mount Stacking Points332
- Stacking HDX Projectors333
- Aligning Stacked HDX Projectors336
Environmental Information339
- Disposal Information341
- Rohs Compliance342
- F.2 Rohs Compliance342
Index345

Barco HDX series User Manual

Table of Contents

Questions and Answers:

Barco HDX series Specifications

Related product manuals

Brand	Barco
Model	HDX series
Category	Projector
Language	English