Brother MFC-9420CN User Manual

Chapter C
C - 2
DR Mode in Use The machine is set to Distinctive Ring
mode. You can not change the
Receive Mode from Manual to another
mode.
Set Distinctive Ring to Off.
See Turning off Distinctive Ring on page 7-8 or 7-13.
Near Waste Toner The waste toner pack is nearly full. Replace the waste toner pack. (See Replacing the
waste toner pack on page C-32.)
No Fusing Unit The fusing unit was not detected. Please install one. (See Fusing unit on page C-35.)
No OPC Belt The OPC belt cartridge is not installed. Install the OPC belt cartridge. (See Replacing the OPC
belt cartridge (OP-4CL) on page C-33.)
No Paper Fed The machine is out of paper or paper
is not properly loaded in the indicated
paper tray.
Refill the paper in the paper tray.
—OR—
Remove the paper and load it again.
No Response/Busy The number you dialled does not
answer or is busy.
Verify the number and try again.
No Toner X
X = C, M, Y, K
(K: Black, C: Cyan, M:
Magenta,
Y: Yellow)
The toner cartridge is not installed
properly.
Reinstall the X toner cartridge. (See the Quick Setup
Guide.)
No TR Roller The transfer roller is not installed. Install the transfer roller. (See Replacing the transfer
roller on page C-39 and follow the steps for properly
installing the roller.)
Not Registered You tried to access a One-Touch or
Speed Dial number that is not
programmed.
Set up the One-Touch or Speed Dial number. (See
Storing One-Touch Dial numbers on page 7-3 and
Storing Speed-Dial numbers on page 7-4.)
Out of Memory The machine’s memory is full. (Fax sending or copy operation in progress)
Press Mono Start or Colour Start to send or copy the
scanned pages.
—OR—
Press Stop/Exit and wait until the other operations in
progress have finished and then try again.
—OR—
Clear the faxes from the memory. (See Out of Memory
message on page 5-3.)
(Printing operation in progress)
Reduce print resolution. (See Advanced tab in the
Software User’s Guide on the CD-ROM.)
—OR—
Clear the faxes from the memory. (See Out of Memory
message on page 5-3.)
—OR—
Add more memory. (See Installing additional memory
on page D-4.)
ERROR MESSAGES
ERROR MESSAGE CAUSE ACTION

Brother MFC-9420CN Specifications

General

Print technology	Laser
Maximum resolution	1200 x 2400 DPI
Economical printing	Yes
Print speed (black, normal quality, A4/US Letter)	31 ppm
Print speed (color, normal quality, A4/US Letter)	8 ppm
Digital sender	No
Number of print cartridges	4
Scanner type	Flatbed scanner
Scanner features	Scan to: e-mail, image, OCR, file
Copier resize	25 - 400 %
Maximum copy resolution	600 x 600 DPI
Maximum number of copies	99 copies
Copy speed (black, normal quality, A4)	31 cpm
Copy speed (color, normal quality, A4)	8 cpm
Faxing	Color faxing
Fax memory	500 pages
Modem speed	33.6 Kbit/s
Fax speed dialing (max numbers)	200
Total input capacity	750 sheets
Maximum input capacity	250 sheets
Auto document feeder (ADF) input capacity	35 sheets
Maximum internal memory	576 MB
Bundled software	ScanSoft PaperPort Presto! PageManager
I/O ports	IEEE-1284 USB 2.0
Dimensions (WxDxH)	483.5 x 514 x 530 mm
Printer management	BRAdmin Professional, MIB-II
Networking features	10Base-T/100Base-TX
All-in-one functions	Fax, Scan
Color all-in-one functions	copy, fax, print, scan
Compatible operating systems	Windows 98(SE)/ Me/ NT WorkStation 4.0/ 2000 Professional/ XP Mac OS 9.1 - 9.2, Mac OS X 10.2.4+
Sustainability certificates	ENERGY STAR
Power consumption (standby)	85 W
Power consumption (PowerSave)	16 W
Power consumption (average operating)	1090 W
Operating temperature (T-T)	10 - 32 °C
Operating relative humidity (H-H)	20 - 80 %
Market positioning	Business