EasyManuals Logo

Cisco TelePresence SX80 User Manual

Cisco TelePresence SX80
231 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #108 background imageLoading...
Page #108 background image
D15107.0 5 Codec SX80 API Reference Guide TC7.3, OCTOBER 2015. Copyright © 2015 Cisco Systems, Inc. All rights reserved. 108
Cisco TelePresence SX80 API Reference Guide
xCommand Cameras SpeakerTrack Whiteboard SetDistance
Set the cameras distance to the whiteboard. This information is needed by the SpeakerTrack 60 to
frame the whiteboard automatically.
Distance: Set distance to whiteboard in centimeters. Use a distance between 0-2000 cm. Use an
accurate measurement for the feature to work seamlessly.
WhiteboardId: The id set for the camera position used for the snap-to-whiteboard feature. Currently
only id 1 can be used.
Requires user role: ADMIN
Parameters:
Distance (r): <0-65534>
WhiteboardId: <0-65534>
Example:
xCommand Cameras SpeakerTrack Whiteboard SetDistance Distance:1000
WhiteboardId:123
xCommand Cameras SpeakerTrack Whiteboard StorePosition
Store the position of one of the cameras on a SpeakerTrack 60 as the Snap to Whiteboard position.
Frame the image so that there is room around the whiteboard for the speaker. To use the Snap
to Whiteboard feature it must be enabled with xConfiguration Cameras SpeakerTrack Whiteboard
Mode and tracking must be enabled with xConfiguration Cameras SpeakerTrack Mode.
Note: You must store a snap-to-whiteboard position for both cameras.
Camera: Select the camera which position you wish to store.
WhiteboardId: You can give the position an id number. Currently the only id that can be used is 1.
Requires user role: ADMIN
Parameters:
Camera (r): <Left/Right>
WhiteboardId: <0-65534>
Example:
xCommand Cameras SpeakerTrack Whiteboard StorePosition Camera:Left
WhiteboardId:123
Conference commands
xCommand Conference ActiveSpeaker Reset
Resets ActiveSpeaker. Normal voice switching is switched back on.
Requires user role: USER
Example:
xCommand Conference ActiveSpeaker Reset
xCommand Conference ActiveSpeaker Set
For manually setting the active speaker in a conference. Overrides normal voice switching.
Target: Identifies local or remote participant.
CallId: Identifies CallID for remote participant. Only relevant if Target is set to "remote".
Requires user role: USER
Parameters:
Target(r): <local/remote>
CallId: <0..65534>
Example:
Example 1
xCommand Conference ActiveSpeaker Set Target: local
Example 2
xCommand Conference ActiveSpeaker Set Target: remote CallID: 3
xCommand Conference DoNotDisturb Activate
This command switches on the Do Not Disturb mode, and the Timeout parameter allows you
to control when it is switched off again. It only takes effect when xConfiguration Conference
DoNotDisturb Mode is set to Timed.
When Do Not Disturb is switched on, all incoming calls are rejected and registered as missed calls.
The calling side receives a busy signal.
Timeout: The number of minutes before Do Not Disturb is switched off. If not set, Do Not Disturb
times out after 1440 minutes (24 hours).
Requires user role: USER
Parameters:
Timeout: <0..1440>
Example:
xCommand Conference DoNotDisturb Activate Timeout: 120
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatus
xCommand

Table of Contents

Other manuals for Cisco TelePresence SX80

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco TelePresence SX80 and is the answer not in the manual?

Cisco TelePresence SX80 Specifications

General IconGeneral
Maximum frame rate60 fps
Supported video modes720p, 1080p
Video formats supportedH.261, H.262, H.263, H.264, H.265
Supported graphics resolutions1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecsG.711, G.722, G.722.1, G.729ab
Noise reductionYes
HDMI ports quantity5
DVI-D ports quantity1
USB 2.0 ports quantity2
Product colorSilver
Rack capacity1U
Number of persons0 person(s)
Analog signal format systemNTSC, PAL
Security algorithmsHTTPS, SSH
Ethernet LAN data rates10, 100, 1000 Mbit/s
Supported network protocolsSIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Storage temperature (T-T)-20 - 60 °C
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 90 %
Sensor type-
Image sensor size- \
Weight and Dimensions IconWeight and Dimensions
Depth309.8 mm
Width442 mm
Height44 mm
Weight3650 g

Related product manuals