Cisco TelePresence SX80 User Manual

D15107.0 5 Codec SX80 API Reference Guide TC7.3, OCTOBER 2015. Copyright © 2015 Cisco Systems, Inc. All rights reserved. 211
Cisco TelePresence SX80 API Reference Guide
xStatus SystemUnit Hardware Module CompatibilityLevel
The Cisco TelePresence endpoints are using a NAND flash memory for general storage. The
endpoints running TC software are manufactured with a new version of the flash memory. Endpoints
having the new version of the flash memory must run software TC4.2.1 or later. Some previous TC
software versions are updated to support the new flash memory. Please check the release note
to find if the new version of the flash memory is supported. If your endpoint does not have the
CompatibilityLevel command it does not have the new flash memory installed.
The result returned when running the command is either 0 or 1:
0 = The system does not have the new flash memory installed.
1 = The system has the new flash memory installed. If downgraded, it can only be downgraded to
previous TC software versions having support for the new version of the flash memory.
Value space of the result returned:
< "1"/ "0 ">
Example:
xStatus SystemUnit Hardware Module CompatibilityLevel
*s SystemUnit Hardware Module CompatibilityLevel: 1
** end
xStatus SystemUnit Hardware MainBoard SerialNumber
Shows the serial number of the main board in the codec.
Value space of the result returned:
<String>
Example:
xStatus SystemUnit Hardware MainBoard SerialNumber
*s SystemUnit Hardware MainBoard SerialNumber: "F1234567"
** end
xStatus SystemUnit Hardware MainBoard Identifier
Shows the revision of the main board in the codec.
Value space of the result returned:
<String>
Example:
xStatus SystemUnit Hardware MainBoard Identifier
*s SystemUnit Hardware MainBoard Identifier: "101400-5 [06]"
** end
xStatus SystemUnit Hardware MonitoringSoftware
The feedback shows the monitoring software id.
Value space of the result returned:
<String>
Example:
xStatus SystemUnit Hardware MonitoringSoftware
*s SystemUnit Hardware MonitoringSoftware: "39"
** end
xStatus SystemUnit Hardware Temperature
The feedback shows the current maximum temperature (degree Celsius) measured in the codec/
system.
Value space of the result returned:
<String>
Example:
xStatus SystemUnit Hardware Temperature
*s SystemUnit Hardware Temperature: "64.0"
** end
xStatus SystemUnit Hardware TemperatureThreshold
Returns information on the maximum temperature for the codec. If this temperature is exceeded the
system automatically shuts down.
Value space of the result returned:
<String>
Example:
xStatus SystemUnit Hardware TemperatureThreshold
*s SystemUnit Hardware TemperatureThreshold: "85"
** end
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatusxStatus

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g