Cisco TelePresence SX80 User Manual

D15107.0 5 Codec SX80 API Reference Guide TC7.3, OCTOBER 2015. Copyright © 2015 Cisco Systems, Inc. All rights reserved. 206
Cisco TelePresence SX80 API Reference Guide
SIP status
xStatus SIP
Shows the top level overview of the SIP status.
xStatus SIP Profile 1 Proxy [1] Status
Shows the status of the communication between the endpoint and the SIP Proxy server.
Active: The communication between the endpoint and the SIP Proxy is active.
DNSFailed: The attempt to establish communication to the DNS server failed.
Off: There is no communication between the endpoint and the SIP Proxy.
Timeout: The attempt to establish communication to the SIP Proxy timed out.
UnableTCP: The system is unable to use TCP as the transport method.
UnableTLS: The system is unable to use TLS as the transport method.
Unknown: The status of the communication is not known.
AuthenticationFailed: Wrong user name or password.
Value space of the result returned:
<Active/DNSFailed/Off/Timeout/UnableTCP/UnableTLS/Unknown/AuthenticationFailed>
Example:
xStatus SIP Profile 1 Proxy 1 Status
*s SIP Profile 1 Proxy 1 Status: Active
** end
xStatus SIP Profile 1 Proxy [1] Address
Shows the address of the SIP Proxy that the system communicates with.
Value space of the result returned:
<String>
Example:
xStatus SIP Profile 1 Proxy 1 Address
*s SIP Profile 1 Proxy 1 Address: "192.0.2.50"
** end
xStatus SIP Profile 1 Secure
Shows the encryption status of the signaling with the SIP Proxy server.
Value space of the result returned:
<True/False>
Example:
xStatus SIP Profile 1 Secure
*s SIP Profile 1 Secure: True
** end
xStatus SIP Profile 1 Verified
Shows whether or not the SSL certificate of the server that the video system / codec tries to regis-
ter to is included in the codec’s trusted CA-list. The server is typically a Cisco VCS or CUCM.
True: The server’s SIP certificate is checked against the trusted CA-list on the codec and found
valid. Additionally, the fully qualified domain name of the server matches the valid certificate.
False: A TLS connection is not set up because the SIP certificate verification failed or the domain
name did not match. Note that the status also returns False when TLS is not used (xConfiguration
SIP Profile 1 DefaultTransport not set to TLS) or certificate verification is switched off (xConfigura-
tion SIP Profile TlsVerify set to Off).
Value space of the result returned:
<True/False>
Example:
xStatus SIP Profile 1 Verified
*s SIP Profile 1 Verified: False
** end
xStatus SIP Profile 1 Authentication
Shows which authentication mechanism is used when registering to the SIP Proxy Server.
Digest: Uses the Digest access authentication method, as specified by RFC 2069.
NTLM: Uses the NTLM authentication method, which is a Microsoft authentication protocol.
Off: No authentication mechanism is used.
Value space of the result returned:
<Digest/Off>
Example:
xStatus SIP Profile 1 Authentication
*s SIP Profile 1 Authentication: Off
** end
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatusxStatus

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g