Cisco TelePresence SX80 User Manual

D15107.0 5 Codec SX80 API Reference Guide TC7.3, OCTOBER 2015. Copyright © 2015 Cisco Systems, Inc. All rights reserved. 70
Cisco TelePresence SX80 API Reference Guide
SystemUnit configuration
xConfiguration SystemUnit Name
Define the system name. The system name will be sent as the hostname in a DHCP request and
when the codec is acting as an SNMP Agent.Define the system name. The system name will be
sent as the hostname in a DHCP request and when the codec is acting as an SNMP Agent.
Requires user role: ADMIN
Value space: <S: 0, 50>
Format: String with a maximum of 50 characters.
Example:
xConfiguration SystemUnit Name: "Meeting Room"
xConfiguration SystemUnit MenuLanguage
This has been replaced with the UserInterface Language setting.
xConfiguration SystemUnit CallLogging Mode
Set the call logging mode for calls that are received or placed by the system. The call logs may then
be viewed via the web interface or using the xCommand CallHistory Get command.
Requires user role: ADMIN
Value space: <Off/On>
Off: Disable logging.
On: Enable logging.
Example:
xConfiguration SystemUnit CallLogging Mode: On
xConfiguration SystemUnit ContactInfo Type
Choose which type of contact information to show in the status field in the upper left corner of the
main display and Touch controller. The information can also be read with the command xStatus
SystemUnit ContactInfo.
Requires user role: ADMIN
Value space: <Auto/None/IPv4/IPv6/H323Id/E164Alias/H320Number/SipUri/SystemName/
DisplayName>
Auto: Show the address which another system can dial to reach this system. The address
depends on the default call protocol and system registration.
None: Do not show any contact information in the status field.
IPv4: Show the IPv4 address as contact information.
IPv6: Show the IPv6 address as contact information.
H323Id: Show the H.323 ID as contact information (see the H323 Profile [1..1] H323Alias ID setting).
E164Alias: Show the H.323 E164 Alias as contact information (see the H323 Profile [1..1] H323Alias
E164 setting).
H320Number: Show the H.320 number as contact information (only applicable if connected to a
Cisco TelePresence ISDN Link gateway).
SipUri: Show the SIP URI as contact information (see the SIP Profile [1..1] URI setting).
SystemName: Show the system name as contact information (see the SystemUnit Name setting).
DisplayName: Show the display name as contact information (see the SIP Profile [1..1]
DisplayName setting).
Example:
xConfiguration SystemUnit ContactInfo Type: Auto
xConfiguration SystemUnit IrSensor
Not applicable in this version.
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatus
xConfiguration

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g