Cisco TelePresence SX80 User Manual

D15107.0 5 Codec SX80 API Reference Guide TC7.3, OCTOBER 2015. Copyright © 2015 Cisco Systems, Inc. All rights reserved. 189
Cisco TelePresence SX80 API Reference Guide
xStatus MediaChannels Call [n] OutgoingAudioChannel [n] Transport RTCP Remote
Protocol
Shows the remote transport protocol used for RTCP for outgoing audio.
The result Unknown is shown when an address is not available, for example during call setup, or for
channels that are not supported by the far-end.
Value space of the result returned:
<UDP/TCP/Unknown>
Example:
xStatus MediaChannels Call 2 OutgoingAudioChannel 127 Transport RTCP
Remote Protocol
*s MediaChannels Call 2 OutgoingAudioChannel 127 Transport RTCP Remote
Protocol: UDP
** end
xStatus MediaChannels Call [n] OutgoingAudioChannel [n] Transport RTP Local Protocol
Shows the local transport protocol used for RTP for outgoing audio.
The result Unknown is shown when an address is not available, for example during call setup, or for
channels that are not supported by the far-end.
Value space of the result returned:
<UDP/TCP/Unknown>
Example:
xStatus MediaChannels Call 2 OutgoingAudioChannel 127 Transport RTP Local
Protocol
*s MediaChannels Call 2 OutgoingAudioChannel 127 Transport RTP Local
Protocol: UDP
** end
xStatus MediaChannels Call [n] OutgoingAudioChannel [n] Transport RTP Remote Protocol
Shows the remote transport protocol used for RTP for outgoing audio.
The result Unknown is shown when an address is not available, for example during call setup, or for
channels that are not supported by the far-end.
Value space of the result returned:
<UDP/TCP/Unknown>
Example:
xStatus MediaChannels Call 2 OutgoingAudioChannel 127 Transport RTP
Remote Protocol
*s MediaChannels Call 2 OutgoingAudioChannel 127 Transport RTP Remote
Protocol: UDP
** end
xStatus MediaChannels Call [n] OutgoingVideoChannel [n] Transport RTCP Local Protocol
Shows the local transport protocol used for RTCP for outgoing video.
The result Unknown is shown when an address is not available, for example during call setup, or for
channels that are not supported by the far-end.
Value space of the result returned:
<UDP/TCP/Unknown>
Example:
xStatus MediaChannels Call 2 OutgoingVideoChannel 127 Transport RTCP
Local Protocol
*s MediaChannels Call 2 OutgoingVideoChannel 127 Transport RTCP Local
Protocol: UDP
** end
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatusxStatus

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g