Cisco TelePresence SX80 User Manual

D15107.0 5 Codec SX80 API Reference Guide TC7.3, OCTOBER 2015. Copyright © 2015 Cisco Systems, Inc. All rights reserved. 153
Cisco TelePresence SX80 API Reference Guide
xStatus Audio Output LocalOutput [n] Loudspeaker
Shows the Loudspeaker mode on the local output. If one or more of the output connectors that are
attached to the local output are connected to a loudspeaker, then this signal should be a reference
signal to the echo canceler and Loudspeaker should be set to On.
You can run the command xStatus Audio Output LocalOutput to find the identity [n] of the output.
Value space of the result returned:
<"On"/"O ff ">
Example:
xStatus Audio Output LocalOutput 4 Loudspeaker
*s Audio Output LocalOutput 4 Loudspeaker: "Off"
** end
xStatus Audio Output LocalOutput [n] Channels
States if the local output channels are mixed into into a mono signal (1) or stereo signal (2).
You can run the command xStatus Audio Output LocalOutput to find the identity [n] of the output.
Value space of the result returned:
<1..2>
Example:
xStatus Audio Output LocalOutput 4 Channels
*s Audio Output LocalOutput 4 Channels: "1"
** end
xStatus Audio Output LocalOutput [n] Connector
Lists the connectors that are attached to the local output.
You can run the command xStatus Audio Output LocalOutput to find the identity [n] of the output.
Value space of the result returned:
<"Line.1"/"Lin e.2"/"HDMI.1"/"HDM I.2">
Example:
xStatus Audio Output LocalOutput 4 Connector
*s Audio Output LocalOutput 4 Connector: "Line.1"
** end
xStatus Audio Output LocalOutput [n] Input [n] Gain
Shows the gain (dB) on the input, when it is connected to the local output. Range from -54 dB to 15
dB, where -54 dB equals Off.
You can run the command xStatus Audio Output LocalOutput to find the identity [n] of the output
and input.
Value space of the result returned:
<-54 ..15>
Example:
xStatus Audio Output LocalOutput 4 Input 2 Gain
*s Audio Output LocalOutput 4 Input 2 Gain: 0
** end
xStatus Audio Output LocalOutput [n] VolumeControlled
Shows whether the volume of this output is controlled by global audio control (Off), or if it is at the
level defined with xCommand Audio Volume Set (On).
Value space of the result returned:
<String>
Example:
xStatus Audio Output LocalOutput 5 VolumeControlled
*s Audio Output LocalOutput 5 VolumeControlled: "On"
** end
xStatus Audio Output RemoteOutput [n] CallId
Shows the CallId for the remote audio output.
You can run the command xStatus Audio Output RemoteOutput to find the identity [n] of the output.
Value space of the result returned:
<1..65534>
Example:
xStatus Audio Output RemoteOutput 9 CallId
*s Audio Output RemoteOutput 9 CallId: 28
** end
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatusxStatus

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g